manualshive.com logo in svg

Komatsu PC500LC-10R, Shop Manual, Page: 187 / 758

Share
Download
Komatsu PC500LC-10R Shop Manual Download Page 187

PRESSURE COMPENSATION CONTROL
FUNCTION OF PRESSURE COMPENSATION CONTROL

• Pressure compensation valves (2) (2 pieces) are installed

at outlet of the downstream and return side of main spool
(4) by each actuator (1).

• The  highest  LS  pressure  is  transmitted  to  the  back  of  all

pressure  compensation  valves  (2),  and  light  load  side  is
throttled.

• When it is throttled until all pressure compensation valves

(2) are balanced, the differential pressures before and after
main spool (4) become the same.

• As a result, the flow rate control in proportion to the travel

of levers (3) in the combined operation becomes available
without influenced by the load.
A: Heavy load
B: Light load
C: LS circuit
1: Actuator
2: Pressure compensation valves
3: Levers
4: Main spool
5: LS shuttle valve
6: Main pump
7: Servo piston

• If the pressure compensation valve is not installed, •••

CLSS  is  a  parallel  circuit,  so  light  load  side  (B)  actuates
earlier than heavy load side (A). As a result, performance
of the simultaneous operation becomes worse.

LS BYPASS PLUG

LS

Abbreviation for Load Sensing

10 STRUCTURE AND FUNCTION

CLSS

PC500LC-10R

10-93

Summary of Contents for PC500LC-10R























































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments