Komatsu PC45MR-30403, Operation And Maintenance Manual, Page: 470 / 475

Explanation of radio equipment............................ 6-24
F
Fan belt - Check tension / Replace.......................4-83
Filter........................................................................ 4-9
Final drive case - Change oil................................ 4-87
Final drive case - Check oil level / Add oil............ 4-82
Floor - Cab specification - Close......................... 3-110
Floor - Cab specification - Open......................... 3-106
Floor - Canopy specification - Close................... 3-108
Floor - Canopy specification - Open................... 3-103
Floor - Close....................................................... 3-108
Floor - Fix securely................................................. 4-4
Floor - Open........................................................3-103
Floor - Open / Close............................................3-101
Floor lock release lever.........................................3-91
Floor tilt fixing bolt - Cab specification - Check... 3-150
Floor tilt fixing bolt - Canopy specification - Check......
.....................................................................3-148
Floor tilt fixing bolt - Check..................................3-148
Frequency - Adjust................................................6-27
Frequency - Auto-preset....................................... 6-27
Fresh and clean lubricants......................................4-2
FRESH/RECIRC air changeover lever................3-211
Fuel......................................................................... 4-6
Fuel - Check level / Add......................................3-146
Fuel and lubricants..............................................3-229
Fuel and lubricants to match the ambient temperature
.........................................................................4-4
Fuel circuit - Bleed air......................................... 3-234
Fuel consumption gauge.......................................3-35
Fuel consumption gauge - Set display..................3-49
Fuel consumption record - Check......................... 3-46
Fuel control dial.....................................................3-79
Fuel gauge............................................................ 3-33
Fuel injection system - Check / Clean...................4-98
Fuel level caution lamp......................................... 3-21
Fuel main filter cartridge - Replace....................... 4-74
Fuel prefilter cartridge - Replace...........................4-71
Fuel prefilter element - Clean................................4-34
Fuel tank - Drain water and sediment................. 3-133
Fuel, coolant and lubricants according to ambient
temperature - Use............................................7-7
Function switches................................................. 3-39
Function switches and guidance icons................. 3-37
Fuse.................................................................... 3-113
Fusible link.......................................................... 3-115
G
Gas spring - Check............................................... 4-57
Gauge display....................................................... 3-32
General attachment such as crusher etc - Operate.....
.......................................................................6-16
General attachment such as crusher etc of machines
with attachment control pedal - Operate........6-16
General attachment such as crusher etc of machines
with proportional lever - Operate................... 6-17
General attachment such as crusher, etc. - Check
points when using.......................................... 6-15
General precautions common to operation and main-
tenance.......................................................... 2-13
General view........................................................... 3-2
GPS synchronization - Set....................................3-67
Grease.................................................................... 4-7
Grease pump holder........................................... 3-116
Ground whole the bottom side of blade to support
machine....................................................... 3-187
H
Handle oil, fuel, coolant, and performing oil clinic...4-5
Handling bucket with hook...................................... 6-4
Handrails and tracks - Use when getting on or off ma-
chine.............................................................. 2-18
Heater - Handle.....................................................6-22
Heater - Use..........................................................6-23
Heater switch........................................................ 6-22
High register range (treble) - Adjust......................6-28
High-pressure hoses and pipings - Handle...........2-46
Horn - Check.......................................................3-147
Horn switch..................................................... 3-80,6-8
Hydraulic breaker..................................................6-34
Hydraulic circuit - Bleed air............................. 4-3,4-58
Hydraulic circuit - Release internal pressure........ 4-96
Hydraulic circuit for machine ready for installation of
attachment - Change-over............................. 6-11
Hydraulic circuit for machine ready for installation of
attachment - Change-over / Connect...............6-9
Hydraulic circuit for machine ready for installation of
attachment - Connect...................................... 6-9
Hydraulic components - Handle............................4-10
Hydraulic oil filter element - Replace.................... 4-85
Hydraulic system - Warm-up operation...............3-165
Hydraulic system caution lamp............................. 3-21
Hydraulic tank - Change oil / Clean strainer......... 4-89
Hydraulic tank - Check oil level / Add oil.............3-138
Hydraulic tank breather element - Replace...........4-80
I
If any problem is found..........................................2-15
If machine monitor shows warning display......... 3-248
Inside operator's compartment............................. 2-14
Inspecting machine............................................... 2-14
Introduction............................................................. 1-4
Investigate and confirm jobsite conditions............ 2-23
J
Jumper cable - Connect......................................3-242
Jumper cable - Disconnect................................. 3-243
INDEX
8-3