manualshive.com logo in svg

Komatsu PC16R-3, Operation & Maintenance Manual

Share
Download
Komatsu PC16R-3 Operation & Maintenance Manual Download Page 137

USE OF THE MACHINE AND RELATED CONTROLS

135

3.3.4 STOPPING THE ENGINE

IMPORTANT

q

The sudden stop of the engine while it is running shortens its life.

q

Do not stop the engine suddenly, except in case of emergency. It is likewise recommended not to stop 
the engine suddenly if it has been running for a long period and is still hot; in this case, let the engine 
run at low idling speed for about 5 minutes, in order to allow it to cool down gradually before stopping it.

1.

Run  the  engine  at  low  idling  speed  for  about  5  minutes,  in 
order to allow it to cool down gradually.

2.

Turn the ignition key (1) to position OFF to stop the engine.

3.

Remove the key (1).

RKA22940

RYA17470

WEAM012405

Summary of Contents for PC16R-3

































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands