manualshive.com logo in svg

Komatsu Galeo PC138US-8, Shop Manual, Page: 301 / 946

Share
Download
Komatsu Galeo PC138US-8 Shop Manual Download Page 301

10 Structure, function and maintenance standard

SEN02553-01

PC138US, USLC-8

43

*2: When the temperature is set at 18.0°C or 32.0°C, the fan speed is kept at “High“. Even if the set tem-

perature is reached, the fan speed remains the same.

*3: When the fan is set at Stop, the air conditioner does not start even if the switch is pressed.

7

Fan switch (Up)
[Numeric keypad: 7]

Controls the fan speed of the air condi-

tioner in 6 levels.
(Low, Medium 1, Medium 2, Medium 3, 

Medium 4, High)

• The air flow increases immediately after 

the air conditioner adjustment screen 
appears.

7a Fan switch (Down) 

• The air flow decreases immediately after 

the air conditioner adjustment screen 
appears.

8

Temperature control  
switch (Up) 

[Numeric keypad: 8]

Controls the temperature inside the cab.

(18.0°C – 32.0°C: Aailable at every 0.5°C)

• The temperature control increases immedi-

ately after the air conditioner adjustment 
screen appears.

8a

Temperature control 

switch (Down)  

[Numeric keypad: 0]

• The temperature control decreases imme-

diately after the air conditioner adjustment 
screen appears.

9

(*2) Auto switch 
[Numeric keypad: 9]

Auto-runs the air conditioner and air 
blower. AUTO light ON: Auto run

• Automatically controls the fan speed, air 

outlet port, internal/external air flow accord-
ing to the temperature setting, immediately 
after the air conditioner adjustment screen 
appears.

10 (*3) Air conditioner 

switch

Turns the air conditioner ON/OFF.

A/C ON lights-up: Manual operation
Light OFF: Stop

• Switches to the air conditioner adjustment 

screen, and pressing it again switches ON/
OFF.

OFF 

io

 ON

11

FRESH/RECIRC 

selector switch

Changes the FRESH/RECIRC.

• Switches to the air conditioner adjustment 

screen, and pressing it again switches 
internal/external air flow.

RECIRC 

io

 FRESH

12 Vent selector switch

Selects the air vent mode from 6 modes.

1. Front
2. Front and rear

3. Front and rear-foot

4. Foot
5. Foot and defroster

6. Defroster

• Switches to the air conditioner adjustment 

screen, and pressing it again switches air 
outlet mode.

• Mode 1, 5 and 6 are not available with auto 

mode.

        o 

 1  

o

  2  

o

  3  

o

  4  

o 

 5 

o 

 6  

o

      I

                                                         

O

        i

      

i

      

i

     

i

      

i

     

i       i

13 OFF switch

Turns the fan and air conditioner OFF.

Light OFF: OFF

• Turns the fan and air conditioner OFF.

14a Guidance icon

a

 See “Guidance icon and function switch.“

14b Function switch

No.

Name

Function

Operation

Summary of Contents for Galeo PC138US-8



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments