background image

 

© 2020 Kolpin Outdoors Inc. 

REV 01 

Windshield Cleaning Information:

 

• 

Remove all dirt, mud, dust and debris from Windshield with water before cleaning.  

• 

Use a mild soap or dishwashing detergent along with a soft sponge or soft cotton cloth to clean Windshield surface. Do not apply in direct sun-
light. Rinse with water immediately and dry with a soft cotton cloth or chamois.   

• 

Always test cleaning agents in a small inconspicuous area prior to cleaning entire panel.  

• 

Never use Windshield cleaning fluids (409, Windex, etc.), gasoline, high alkaline cleaners, or solvents.   

• 

Never use abrasives, brushes, razor blades, scrapers, squeegees, gloves or dirty cloths.  

For additional assistance, please contact Kolpin customer service department at   

(877) 956-5746 or (763) 478-5800 or email 

[email protected]

 

One Year Limited Warranty 

 

For the period of one (1) year from the purchase date, Kolpin will replace for the original purchaser, free of charge, any part or parts found upon ex-

amination by Kolpin to be defective in material, workmanship, or both.  

All transportation costs incurred submitting product to Kolpin for warranty consideration must be borne by the purchaser. If Kolpin determines that the 

product must be returned to the factory for credit, please call 1-877-956-5746 for a Return Merchandise Authorization (RMA) number and shipping 

instructions.  

This warranty does not apply to parts that have been damaged by accident, alteration, abuse, improper maintenance, normal wear, or other causes 
beyond the manufacturer’s control. In order to protect you and your ATV, certain parts of the accessory system and/or hardware are designed to fail 
when the equipment is over-stressed. Parts that are lost due to loosening and improper maintenance are not covered under warranty. This warranty 
does not cover removal or reinstallation labor fees of the plow system and related components. 

Peripheral products such as engines, electric motors, and actuators may carry an original manufacturer’s warranty. Most hardware is general in na-
ture and is easily obtained locally. Be sure to replace with minimum metric class 8.8 specification.  

 

TO AVOID SERIOUS INJURY OR DEATH: 

1. 

DO NOT TRAILER VEHICLE FACING REARWARD WITH WINDSHIELD INSTALLED.  AIRFLOW MAY CAUSE 
WINDSHIELD TO SEPARATE FROM VEHICLE, RESULTING IN AN ACCIDENT AND SEVERE INJURY OR 
DEATH.  REMOVE WINDSHIELD OR TRANSPORT VEHICLE IN ENCLOSED TRAILER. 

2. 

UTVs ARE TO ONLY BE DRIVEN WITH CLEAN WINDSHIELDS FOR DRIVING VISIBILITY.  IF DIRT OR DEBRIS 
ACCUMULATES ON THE WINDSHIELD WHEN RIDING, STOP THE UTV AT THE NEXT SAFE LOCATION ON 
THE TRAIL TO CLEAR OFF THE WINDSHIELD BEFORE YOU RESUME RIDING. 

 

3. 

ONLY INSTALL WINDSHIELDS THAT ARE DESIGNED FOR THE MAKE AND MODEL OF THE UTV.  INSTALLA-
TION OF A WINDSHIELD THAT WAS NOT DESIGNED FOR THE UTV MAKE AND MODEL CAN IMPACT WIND-
SHIELD DURABILITY AND PERFORMANCE.

 

4. 

READ AND UNDERSTAND WINDSHIELD INSTRUCTION SHEETS AND UTV OWNER MANUAL BEFORE WIND-
SHIELD INSTALLATION OR OPERATING THE VEHICLE. 

 

5. 

PERIODICALLY CHECK FOR WEAR AND TIGHTNESS OF ALL FASTENERS.  ALWAYS INSPECT BEFORE AND 
AFTER RIDING OR TRAILERING. REPLACE OR RE-TORQUE FASTENERS AS NECESSARY.

 

 

!

 

 

!

 

DANGER

 

Summary of Contents for 1466







Reviews: