Kollmorgen AKD series Installation Manual Download Page 35

Page: 35 / 216

7.2 Ambient Conditions, Ventilation, and Mounting Position

Storage

Transport

Surrounding air tem-
perature in operation

0 to +40 °C under rated conditions
+40 to +55 °C with continuous current derating 4 % per Kelvin

Humidity in operation

Relative humidity 5 to 85%, no condensation, class 3K3

Site altitude

Up to 1000 meters above mean sea level without restriction
1,000 to max. 2,500 meters above mean sea level with power
derating 1.5%/100 m

Pollution level

Pollution level 2 as per IEC 60664-1

Vibrations

Class 3M1 according to IEC 60721-3-3

Enclosure protection

IP 20 according to IEC 60529

Mounting position

Vertical, (

➜

# 69)

Ventilation

Built-in fan (except AKD-x00306 type)

The drive shuts down (fault F234, (

➜

# 202), motor has no

torque) in case of excessively high temperature in the control cab-
inet. Make sure sufficient forced ventilation is supplied within the
control cabinet.

7.3 Mechanical Data

Mechanical data

Units

AKD-

x00306

AKD-

x00606

AKD-x01206

AKD-

x02406

Weight (standard width)

1.1

3.7

Weight (extended width)

1.3

2.2

Height, without connectors

168

196

248

Height, with connector

200

225

280

Standard Width front/back

54/59

72/78.4

96/100

Extended Width front/back

84/89

91/96

96/100

Depth, without connectors

156

187

228

Depth, with connectors

185

< 215

<265

Mechanical data

Units

AKD-

x00307

AKD-

x00607

AKD-

x01207

AKD-

x02407

AKD-

x04807

Weight (standard width)

2.7

5.3

11.5

Weight (extended width)

2.9

5.5

11.7

Height, without connectors

256

306

385

Height, with connector

290

340

526

Standard Width front/back

65/70

99/105

185/185

Extended Width front/back

95/100

99/105

Depth, without connectors

185

228

225

Depth, with connectors

<225

<265

AKD Installation | 7 Technical description and data

Kollmorgen | kdn.kollmorgen.com | October 2017

Summary of Contents for AKD series

























































































































































































































Search results

Summary of Contents for AKD series

Reviews:

Related manuals for AKD series

Brands by name

Popular brands

Kollmorgen AKD series, Installation Manual

Search results

Summary of Contents for AKD series

Reviews:

Related manuals for AKD series

Brands by name

Popular brands