Kohler CURTIS 3401T Manual Download Page 62

Page: 62 / 62

APPENDIX B — SPECIFICATIONS

Curtis Model 3401T – August 2022

Return to TOC

pg. 56

APPENDIX B — SPECIFICATIONS

Nominal Voltage

12–96 VDC

Minimum Voltage

8 VDC

Maximum Voltage

120 VDC

Operating Current

•

Keyswitch on

: 33–207mA

•

Keyswitch off

: 25–112mA

•

LCD heater on

: 566–801mA

Dimensions (W × L × H)

160 x 102 x 49.7 mm

Operating Temperature

•

With the LCD heater

: –40°C to +70°C

•

Without the LCD heater

: –20°C to +70°C

Storage Temperature

–40°C to +85°C

Humidity

Designed to the following requirements:

•

Soak

: EN 60068-2-78

•

Cyclic

: EN 60068-2-30

Ingress Protection

Designed to the requirements of EN 60529:

• Face is sealed to IP65.
• Rear is sealed to IP65 for electronic components and to IP40 for the connector.

Optional parts can increase the connector’s protection to IP54.

Salt Spray (Fog)

Designed to the requirements of ASTM B 117 as per SAE J1810.

Shock

Designed to the requirements of EN 60068-2-27.

Vibration

Designed to the following requirements:

•

General

: EN 60068-2-6

•

Random

: EN 60068-2-64

•

Resonance

: EN 60068-2-6

Safety

Designed to the requirements of EN 61010-1: 2010, Part 1. General safety

requirements for measurement, control and laboratory use.

Designed to the following requirements:

•

EMC:

EN 12895:2015+A1:2019

•

Low Voltage Directive (LVD):

EN 60204-1:2018, 2014/35/EU

•

RoHS:

RoHS directive 2015/863/EU (RoHS 3)

UL recognized component as per UL 583.

Model Encodement

The model number encodement is 3401T-

ZYYY

where:

•

indicates whether the model includes the optional LCD heater:

–

5 = not included

–

7 = included

•

YYY

is a sequential number code.

Note:

Regulatory compliance of the complete system with the 3401T installed is the responsibility of the OEM.

Summary of Contents for CURTIS 3401T































































Search results

Summary of Contents for CURTIS 3401T

Reviews:

Brands by name

Popular brands

Kohler CURTIS 3401T, Manual

Search results

Summary of Contents for CURTIS 3401T

Reviews:

Brands by name

Popular brands