background image

9. “Lady care” 

Cleansing suitable for menstruation. In Idle mode, press this button to begin 

function. The nozzle reaches out to work and water temp is set to the highest 

level (39°C), water pressure is set to 2-level, cleaning position set as default. 

Water temp/water pressure not adjustable, cleaning position is adjustable in 

this mode, automatic ends after cleaning for 2 mins. Press Stop to end. 

10. “Child” 

Warm water gentle cleaning, suitable for children. In Idle mode, press this 

button to enter function. The nozzle reaches out to work and nozzle position is 

at the front (5 level), mini water pressured level) and the water temp is mid-

grade (36°C) After washing 30s to end or press Stop to end. Under this mode, 

cleaning position/ water pressure /water temp are not adjustable. 

11. Position 

 

Select from five levels, adjusting the satisfied position to clean by pressing 

+

 or 

 buttons. 

Note:

 Under oscillating cleaning, the nozzle position adjustment is unavailable 

12. “Super” 

Strong wash mode. In Idle mode, press this button to enter the powerful 

washing mode, nozzle reaches out to work and the hole starts to effluent. 

Water pressure is highest level, after washing 2mins to end. Press Stop to end. 

13. “Auto” 

“One solution”, an automatic sequence performing Rear Wash (40 seconds), 

Oscillate Wash (20 seconds), Warm Air Dryer (2 minutes), then stop. Press this 

button to start in Idle mode, and press Stop to end. 

14. Water Temp 

The water temperature can be adjusted in 4 levels: 

Room temperature 

(No light) 

33°C 

(Blue) 

36°C 

(Green) 

39°C 

(Red) 

Press the water temp button to cycle through the settings. 

15. ECO 

Low power mode. Press this button, the corresponding indicator blink on 

control panel in standby, after leaving the seat for 1.5 minutes then enter 

power saving mode. Under this mode, seat temp is kept at 25°C and the 

settings before power saving are automatically restored the next time. 

16. Deodoriser 

 

Press this button to start deodorising, indicator on the control panel lights up. 

Press again to close. 

Note:

 During drying, the deodorising function is temporarily stopped and it will 

automatically start again after the drying is completed. When a person leaves 

the seat, the deodorising function will continue to work automatically after 90 

seconds. 

17. Power 

Press this button to enter standby mode. All lights will be off. When pressed 

again, the device will power on and the Power indicator light will be on. 

 

 

 

Note:

 

Idle mode means rear wash, front wash, dryer, flush, etc. are not enabled. Child wash, 

one solution, strong wash, lady care must be enabled in idle mode.

 

Summary of Contents for KASMABIDETA





























Reviews: