manualshive.com logo in svg

Kodak HEALTH SCIENCES X-Omat Clinic 1, Installation Instructions Manual

Share
Download
Kodak HEALTH SCIENCES X-Omat Clinic 1 Installation Instructions Manual Download Page 8

INSTALLATION INSTRUCTIONS

8

September 1995 – 981088

Section 2: Installing the PROCESSOR

Moving the PROCESSOR to the Work Area

Warning

The unpacked, empty PROCESSOR weighs approximately 84 kg (185 lb).  Use 2 people to move it.  The PUMPS
are heavy and are located in the back of the PROCESSOR.  Rotate the PROCESSOR so that each person supports

1

⁄

2

 the weight of the PROCESSOR.

[1] Move the PROCESSOR to the work area where you plan to install it.  When possible move the PROCESSOR

in its upright position.

(a) If the PROCESSOR does not fit through the door opening of the work area, do the steps below.

1. Check that the BACK ACCESS PANEL and DRIVE SIDE ACCESS PANEL are removed.  If not,

loosen the 2 SCREWS on each PANEL and remove the PANEL.

2. Check that the FRONT ACCESS PANEL is installed.  The FRONT ACCESS will protect the FILM

DETECTOR ASSEMBLY from damage when moving the PROCESSOR through a narrow door
opening.

3. To reduce space requirements, check that the LEVELING FEET are rotated up into the PROCESSOR

as far as possible.

4. Rotate the PROCESSOR so that the non-drive side faces down.  See the figure for the dimensions of

the PROCESSOR with the TOP COVER and PANELS removed.

5. To reduce space requirements even more, unscrew the MOUNTING BRACKET for the

INTERLOCK SWITCH and let the INTERLOCK SWITCH hang inside the PROCESSOR.

Figure 4

Moving the PROCESSOR through a Narrow Door Opening

H130_0133HA

41.3 cm

66.7 cm

(26 1/4 in.)

(16 1/4 in.)

(27 1/4 in.)

69.2 cm

34.3 cm

(13 1/2 in.)

non-drive

FRONT ACCESS

PANEL

side

H130_0133HCB

drive
side

BRACKET

MOUNTING

INTERLOCK
SWITCH

Summary of Contents for HEALTH SCIENCES X-Omat Clinic 1













































































Reviews:

No comments

Brands by name

Popular brands

Load more brands