Kodak DryView 8150 User Manual Download Page 169

Page: 169 / 178

October 4, 2004

7F3319

7-1

Film Technical Information

General Description

This section describes the characteristics of

Kodak DryView

Laser Imaging

Film, not the operation of the

Kodak DryView

8150 Laser Imager.

DryView

Laser Imaging Film is a high-resolution, infrared-sensitive,
photothermographic film designed specifically for the family of

Kodak

DryView

Laser Imagers.

DryView

Laser Imaging Film is packaged in

daylight load packages, available in blue or clear, 7-mil polyester base.
The 8150 Laser Imager accepts three film sizes:

• (28 x 35 cm) 11 x 14 in.

• (35 x 35 cm) 14 x 14 in.

• (35 x 43 cm) 14 x 17 in.

Spectral Sensitivity

DryView

Laser Imaging Film is infrared sensitive and has been sensitized to

the infrared laser diode of

DryView

Laser Imagers. When handled

according to instructions on the daylight-load film package, safelights are
not needed. If you remove undeveloped film from the daylight load
package, you will need a darkroom setting and a green safelight.

Summary of Contents for DryView 8150



















































































































































































Search results

Summary of Contents for DryView 8150

Reviews:

Related manuals for DryView 8150

Brands by name

Popular brands

Kodak DryView 8150, User Manual

Search results

Summary of Contents for DryView 8150

Reviews:

Related manuals for DryView 8150

Brands by name

Popular brands