Kodak DryView 8150 User Manual Download Page 144

Page: 144 / 178

4-20

7F3319

October 4, 2004

Adding a Modality

Setting up the Text
(Annotation) Box

This parameter allows you to select items to be printed in a "text box" on
the bottom of each sheet of film.

1. Select

Film Text

to display the items you can select.

2. Select

Hospital name

if you wish to include the name of your

hospital in the annotation box. A check will display adjacent to the
field.

a. Select

(Edit Hospital name)

and touch

b.Use the keypad to enter the name.

c. Touch

3. Select any or all of the other items on the screen. A check will display

adjacent to each item you select.

4. Touch the

Back

arrow to return to the Modality Defaults screen.

Summary of Contents for DryView 8150



















































































































































































Search results

Summary of Contents for DryView 8150

Reviews:

Related manuals for DryView 8150

Brands by name

Popular brands

Kodak DryView 8150, User Manual

Search results

Summary of Contents for DryView 8150

Reviews:

Related manuals for DryView 8150

Brands by name

Popular brands