manualshive.com logo in svg

kobi NET-KOBI-IP-16CH, User Manual

Share
Download
kobi NET-KOBI-IP-16CH User Manual Download Page 159

 

 

159 

 

12.3

 

Importing/Exporting Configuration Files 

Purpose: 

The configuration files of the NVR can be exported to local device for backup; and the configuration files of one 
NVR can be imported to multiple NVR devices if they are to be configured with the same parameters. 

Steps: 

1.

 

Enter the Import/Export Configuration File interface. 

Menu > Maintenance >Import/Export 

 

Figure 12. 11

 

Import/Export Config File

 

 

2.

 

Click the 

Export

 button to export configuration files to the selected local backup device. 

3.

 

To import a configuration file, select the file from the selected backup device and click the 

Import

 button. 

After the import process is completed, you must reboot the NVR. 

Note: 

After having finished the import of configuration files, the device will reboot automatically. 

Summary of Contents for NET-KOBI-IP-16CH






















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands