background image

Model 7166 Electric Helm 

Kobelt Manufacturing Co. Ltd. 

 

Rev A

 

mnl7166.docx

 

12 of 17 

6

 

T

ROUBLESHOOTING

 

If you encounter problems with the operation of your product, please refer to the trouble-
shooting suggestions before contacting Kobelt for assistance. If the steps below do not 
resolve your issue, please reach out either Kobelt directly or our Dealers in your area.  

Table 4: Common Solutions 

Problem 

(Issue encountered) 

Cause 

 (What it means) 

Corrective Action 

(What to do) 

Helm action is 
reversed. 

Wiring is backwards. 

Swap the POT+ and POT- output 
wires to their respective system 
and handle connections. 

Helm does not move 
rudder at all. 

The rest of the system 

isn’t hooked 

up correctly. 

Check system wiring.  
Confirm wiring to Stacked FFU 
Lever.  
 

Broken potentiometer or 
contact. 

Use a multi-meter to monitor the 
resistance of the wiring between 
potentiometer contacts.  
Check for normal operation of the 
potentiometer by measuring the 
connection while moving the 
Stacked FFU Lever.  
Check potentiometer directions.  
Replace any damaged 
potentiometers. 

Wiring is wrong. 

Check wiring. 
Refer to system design drawing for 
proper wiring. 
 
  

 

 

 

Summary of Contents for 7166 Electric Helm


















Reviews: