2
These instructions should be read carefully and retained after installation by the end user for
future reference and maintenance.
These instructions should be used to aid installation of the following products:
T8136EMHF/T8158EMHF/T8170EMHF/T8236EMHF/T8258EMHF/T8270EMHF
GENERAL INSTRUCTIONS
SAFETY
INSTALLATION
• Installation of this luminaire should only be carried out by a qualified electrician or competent
person to the current Building and IEE Wiring Regulations (BS7671)
• Please isolate mains prior to installation/maintenance
• Check the total load on the circuit (including when this luminaire is fitted) does not exceed the
rating of the circuit cable, fuse or circuit breaker
• Please note the IP (Ingress of Protection) rating of this luminaire when deciding the location for
installation
• This product is Class I and requires an earth
• This product is IP20 rated
• Provide power to the point of installation
• Remove the two screws on top of the fitting (see Fig 1)
• Remove the cover plate
• Mark the location of the fixing holes and drill the holes ensuring not to infringe with any joists, gas/
water pipes or electrical cable
• Bring the power cable into the luminaire
• Secure luminaire to the surface
• For switched maintained operation connect the Permanent Live (brown), Neutral (blue), Earth
(yellow and green) and Switched Live via the terminal connector (see Fig 2)
Fig 1 (single fitting shown)
Fig 2
T8XXXHF series
These instructions should be read carefully and retained after installation by the end user for future reference and
maintenance.
These instructions should be used to aid installation of the following products:
T8118HF/T8136HF/T8158HF/T8170HF/T8218HF/T8236HF/T8258HF/T8270HF
SAFETY
•
Installation of this luminaire should only be carried out by a qualified electrician or competent person to the
current Building and IEE Wiring Regulations (BS7671)
•
Please isolate mains prior to installation/maintenance
•
Check the total load on the circuit, including when this luminaire is fitted, does not exceed the rating of the
circuit cable, fuse or circuit breaker
•
Please note the IP (Ingress of Protection) rating of this luminaire when deciding the location for installation
•
This product is Class I and requires an earth
•
This product is IP20 rated
INSTALLATION
•
Provide power to the point of installation
•
Remove two screws on top of the fitting (see Fig 1)
Fig 1 (single fitting shown)
•
Remove the cover plate
•
Mark the location of the fixing holes and drill the holes ensuring not to infringe with any joists, gas/water pipes or
electrical cable
•
Bring the power cable into the luminaire
•
Secure luminaire to the surface
•
Connect the Live (brown), Neutral (blue) and Earth (yellow and green) via the three-way terminal connector (see
Fig 3)
Fig 3
•
Fix the T8 holders into place at either end of the fitting and attach the top cover screws
•
Fit an appropriate T8 tube by locating the pins into the lamp holders and rotating 90 degrees
•
Switch on power supply and check for correct operation
Remove screws
Neutral (Blue)
N
L
Live (Brown)
E
Earth (Green/Yellow)
T8XXXEMHF series
These instructions should be read carefully and retained after installation by the end user for future reference and
maintenance.
These instructions should be used to aid installation of the following products:
T8136EMHF/T8158EMHF/T8170EMHF/T8236EMHF/T8258EMHF/T8270EMHF
SAFETY
•
Installation of this luminaire should only be carried out by a qualified electrician or competent person to the
current Building and IEE Wiring Regulations (BS7671)
•
Please isolate mains prior to installation/maintenance
•
Check the total load on the circuit, including when this luminaire is fitted, does not exceed the rating of the
circuit cable, fuse or circuit breaker
•
Please note the IP (Ingress of Protection) rating of this luminaire when deciding the location for installation
•
This product is Class I and requires an earth
•
This product is IP20 rated
INSTALLATION
•
Provide power to the point of installation
•
Remove two screws on top of the fitting (see Fig 1)
Fig 1 (single fitting shown)
•
Remove the cover plate
•
Mark the location of the fixing holes and drill the holes ensuring not to infringe with any joists, gas/water pipes or
electrical cable
•
Bring the power cable into the luminaire
•
Secure luminaire to the surface
•
For switched maintained operation connect the Permanent Live (brown), Neutral (blue), Earth (yellow and green)
and Switched Live via the terminal connector (see Fig 3)
Fig 3
•
Connect the battery to the inverter via the connector
•
Fix the T8 holders into place at either end of the fitting and attach the top cover screws
•
Fit an appropriate T8 tube by locating the pins into the lamp holders and rotating 90 degrees
•
Switch on power supply and check for correct operation
Remove screws
