manualshive.com logo in svg

Knick SensoGate WA 131 H, User Manual

Share
Download
Knick SensoGate WA 131 H User Manual Download Page 34

34

Lubricants, O-Rings

SensoGate® WA 131 H 

For fittings used in the chemical industry, the lubricant Syntheso Glep1 (silicone-free) is applied.  

For fittings used in the pharmaceutical / food industry (when FDA conformity is required),  

the lubricant Beruglide L (silicone-free) is applied (registered according to NSF-H1). 

These lubricants are silicone-free.

On request, the lubricant Paraliq GTE 703 can be applied (excellent lubricating properties also 

at increased temperatures and for a large number of travel movements). This lubricant contains 

 silicone and is only used as special application on specific request.

Application

Pharma / Food

Chemistry / Wastewater

Lubricant

Beruglide L

(silicone-free)

FDA-conforming

NSF-H1-registered

Paraliq GTE 703

(containing silicone)

FDA-conforming

(USDA H1)

Syntheso Glep 1 

(silicone-free)

Materials of 

 elastomeric  gaskets
FKM

X

X

X

FFKM

X

X

X

EPDM

X

X

X

Summary of Contents for SensoGate WA 131 H

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands