manualshive.com logo in svg

Knick SensoGate WA 131 H, User Manual

Share
Download
Knick SensoGate WA 131 H User Manual Download Page 12

12

Installing the Inlet Hose (Optional)

SensoGate® WA 131 H

D

F

E

G

H

As delivered, the inlet port is sealed with a plug 

(D)

. 

This sealing plug prevents that process fluid leaks 

from the inlet when the probe is moved.

Specifications

Thread: 

 

   G 1/8 internal, inlet port 

Length: 

 

   3 

meters

Nominal width:   DN 8

Materials:   Hose 

    EPDM

      Hose 

nipple 

  stainless 

steel

      O-ring 

8 

x 

1.5 

 

 EPDM

      O-ring 

4.5 

x 

1.5 

 EPDM

Completely mounted outlet and inlet hoses

Before connecting the inlet hose 

(E)

, first screw the 

connection piece 

(G)

 into the rinse connection 

(H)

. 

Before connecting the inlet hose, you must remove 

the plug (10 mm A/F) 

(D)

.

Screw the inlet hose 

(E)

 to the connection piece 

(G)

 

using coupling nut 

(F)

. If required, you can easily 

disconnect the hose by screwing off the coupling 

nut 

(F)

.

For safe operation of the WA 131 H sensor lock-gate, the sealing plug or the inlet hose 

(option) must be mounted on the inlet port.

Summary of Contents for SensoGate WA 131 H

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands