Knick Protos LDO 3400-170 User Manual Download Page 44

Page: 44 / 64

Menu Display

Diagnostic functions

Opening the Diagnostics Menu

From the measuring mode:

Press

menu

key to select menu.

Select diagnostics using arrow keys,

press

enter

to confirm.

The “Diagnostics” menu gives an

overview of all functions available.

Functions which have been set as

“Favorite” can be directly accessed

from the measuring mode.

Diagnostic Functions

General status information of the measuring system

Select menu: Diagnostics - Message list

Message List

Shows the currently activated warning

or failure messages in plain text.

Menu selection

Return to meas

82.3 %Air

25.6°C

Select:

[enter]

Lingua

Diagnostics

Return

23.7 °C

Set favorite

82.3 %Air

Logbook

Message list

Device description

FRONT module

Message list

Return

25.6°C

82.3 %Air

Warn

BASE module

8 messg.

Point of meas description

Warn Temp alarm HI

Saturation %Air Alarm HI
Fail Wrong ISM sensor

Warn Tolerance band

Warn Zero range

D062

P018

D013
P210

P030

Sensocheck

P092

Number of messages

When there are more than 7 messages, a verti-
cal scrollbar appears. Scroll with the up/down
arrow keys.

Module identifier

Specifies the module that has generated the
message.

Message identifier

See message list for description.

he displa

y ma

y v

y depending on the devic

e v

ersion.

Summary of Contents for Protos LDO 3400-170

































































Search results

Summary of Contents for Protos LDO 3400-170

Reviews:

Related manuals for Protos LDO 3400-170

Brands by name

Popular brands

Knick Protos LDO 3400-170, User Manual

Search results

Summary of Contents for Protos LDO 3400-170

Reviews:

Related manuals for Protos LDO 3400-170

Brands by name

Popular brands