Knick Protos LDO 3400-170 User Manual Download Page 39

Page: 39 / 64

Menu Display

Sensor monitor

Opening the Diagnostics Menu

From the measuring mode:

Press

menu

key to select menu.

Select diagnostics using arrow keys,

confirm by pressing

enter

Then select the LDO module.

The Diagnostics menu gives an over-

view of all diagnostics functions avail-

able. Messages set as “Favorite” can

be called directly from the measuring

mode using a softkey.

To configure, select:

Parameter setting / System control /

Function control matrix.

Sensor Monitor

Shows the data provided by the

sensor.

Important function for diagnostics and

validation!

Menu selection

Return to meas

23.0 °C

Select:

[enter]

Lingua

83.3 %Air

Sensor SE 740

Return

23.0 °C

83.3 %Air

Cal record

Sensor diagram OXY

Sensor wear monitor

Set favorite

Sensor monitor

Return

23.0 °C

83.3 %Air

Ext. pressure transmitter

Partial pressure

Temperature

2500 mbar

207.6 mbar

26.2 °C

Current input

Sensor operating time

0.00 mA

43 h

Module Diagnostics

Diagnostics / Module LDO ...

he displa

y ma

y v

y depending on the devic

e v

ersion.

Summary of Contents for Protos LDO 3400-170

































































Search results

Summary of Contents for Protos LDO 3400-170

Reviews:

Related manuals for Protos LDO 3400-170

Brands by name

Popular brands

Knick Protos LDO 3400-170, User Manual

Search results

Summary of Contents for Protos LDO 3400-170

Reviews:

Related manuals for Protos LDO 3400-170

Brands by name

Popular brands