manualshive.com logo in svg

Knick Portavo 904, User Manual

The Knick Portavo 904 User Manual is an essential resource for unlocking the full potential of this cutting-edge device. Available for free download at manualshive.com, this comprehensive manual provides step-by-step instructions, detailed diagrams, and insightful tips to ensure optimal performance and efficient use of the Knick Portavo 904.

Share
Download
background image

17

Calibration

Measurement

cal

CAL
CELL CONST.

The conductivity will be shown in the display and 
can be compared with a reference solution (tem-
perature-corrected).

Value blinks 

Use 



 to set the cell constant value.

cal

Calibration is performed. Display: CELL CONSTANT. 
The meter then automatically returns to measuring mode.

CELL CONST Calibration 

(Calibration by entry of cell constant)

The calibration method is selected in the configuration menu. 

Measurement

cal

CAL
COND

Dip sensor in solution. 

Value blinks 

Use 



 to set the temperature-corrected conduc-

tivity value. 

Note

: Here, the meter does not perform 

a temperature compensation!

cal

Calibration is performed. Display: CELL CONSTANT. 
The meter then automatically returns to measuring mode.

COND Calibration 

(Calibration by entry of conductivity)

The calibration method is selected in the configuration menu. 

Summary of Contents for Portavo 904























































Reviews:

No comments

Related manuals for Portavo 904

3nh HG Series Operation Manual preview
HG Series
Brand: 3nh Pages: 10
KROHNE AF-E 400 Quick Start Manual preview
AF-E 400
Brand: KROHNE Pages: 34
SAGEMCOM UM20 User Manual preview
UM20
Brand: SAGEMCOM Pages: 33
KBR 18S Operating Instructions And Assembly Manual preview
18S
Brand: KBR Pages: 12
Halo Photonics Stream Line Pro Hardware And Software Manual preview
Stream Line Pro
Brand: Halo Photonics Pages: 45
Dive Perfect Stubby LED-1500 User Manual preview
Stubby LED-1500
Brand: Dive Perfect Pages: 4
Sage RIO SIX Instruction Manual preview
RIO SIX
Brand: Sage Pages: 75
RaySafe ThinX Intra User Manual preview
ThinX Intra
Brand: RaySafe Pages: 2
STATICO SPP Series Operating Manual preview
SPP Series
Brand: STATICO Pages: 21
AVAZZIA Med-Sport OTC Manual preview
Med-Sport OTC
Brand: AVAZZIA Pages: 18
RX EPA 2000 Installation Instructions Manual preview
EPA 2000
Brand: RX Pages: 8
Geokon GK-604 User Manual preview
GK-604
Brand: Geokon Pages: 19
R&S 1321.1111.02 Getting Started preview
1321.1111.02
Brand: R&S Pages: 100
Bürkert 8222 ELEMENT NEUTRINO Operating Instructions Manual preview
8222 ELEMENT NEUTRINO
Brand: Bürkert Pages: 72
UNISENSE Microsensor Multimeter Getting Started Manual preview
Microsensor Multimeter
Brand: UNISENSE Pages: 8
Hanna Instruments HI 38018 Instruction Manual preview
HI 38018
Brand: Hanna Instruments Pages: 2
TA Instruments TGA 2050 Operator'S Manual preview
TGA 2050
Brand: TA Instruments Pages: 130
Bushnell TOUR V4 SHIFT User Manual preview
TOUR V4 SHIFT
Brand: Bushnell Pages: 76

Brands by name

Popular brands

Load more brands