Knick Portavo 904 OXY User Manual Download Page 17 | Manualshive

Page: 17 / 50

background image

17

Calibration

Measurement

cal

CAL
ZERO CAL

xxx
nA
PRESS CAL blinks

Place sensor in oxygen-free medium (e.g.,
nitrogen 5.0) and wait until the measured
values have stabilized.

cal

CAL DATA

Calibration is performed.
Please wait.

Date
ZERO P. xxx nA

Zero calibration data is displayed.

Date
SLOPE xxx nA

Slope calibration data is displayed.

The meter then automatically returns to measuring mode.

ZERO CAL Calibration

(Zero calibration with oxygen-free medium)
The calibration method is selected in the configuration menu.

Note: To abort calibration, you can press meas at any time.

Calibration

«
...
15
16
17
18
19
...
»

Summary of Contents for Portavo 904 OXY



















































Reviews:

No comments

Related manuals for Portavo 904 OXY

Brand: Keithley Pages: 48

Brand: CAENels Pages: 75

Brand: jenway Pages: 50

Brand: jenway Pages: 62

Brand: Keeler Pages: 54

Brand: Samsara Pages: 16

Brand: Yamaha Pages: 12

Brand: Technoline Pages: 1

Brand: OHAUS Pages: 71

Brand: Guru Home Systems Pages: 20

Brand: Bogen Pages: 14

Brand: Kurzweil Pages: 12

Brand: ICP DAS USA Pages: 71

Brand: CONDTROL Pages: 11

Brand: Milwaukee Pages: 17

Brand: Hanna Instruments Pages: 16

Brand: AVAZZIA Pages: 18

Brand: Hanna Instruments Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands