KNF N87.9 Operating And Installation Instructions Download Page 15 | Manualshive

Page: 15 / 32

KNF N87.9 Operating And Installation Instructions Download Page 15

Diaphragm pump N87.9

Installation and connection

Translation of Original Operating and Installation Instruction, english, KNF 121538-121541 11/22

15

6 Installation and connection

Only install the pumps in accordance with the operating parameters and
conditions described in Chapter

3 Technical data

.

à

Observe the safety instructions (see Chapter Safety).

DANGER

Risk of dangerous gas mixtures during pump op-
eration

Depending on the medium being transferred,
breakage of the media-contacting components
can result in a dangerous mixture if the medium
mixes with the air in the compressor housing or
the surroundings.

à

Before using a medium, check the compati-
bility of the media-contacting components
(see

3 Technical data

) with the medium.

6.1 Installing the pump

à

Store the pump at the installation site to allow it to adapt to the ambient
temperature before installation (condensation must not be allowed to
form).

Mounting dimensions

à

For mounting dimensions, see the following figures:

Fig.3 Mounting dimensions N87

«
...
13
14
15
16
17
...
»

Summary of Contents for N87.9

































Reviews:

No comments