KNF FK 1100 Installation Instructions Manual Download Page 10 | Manualshive

Page: 10 / 22

KNF FK 1100 Installation Instructions Manual Download Page 10

Installation

Installation Instructions FK 1100

KNF Flodos 178057_MA_FK1100_EN_00.docx

10

3.3 Connecting the fluid system

Use suitable means to check the fluid connection for leaks.

For more information regarding dimensions, please refer to the
data sheet.

3.4 Electrical connection

For terminal assignment, output data, and control requirements,
please refer to the data sheet.

Observe the regulatory requirements for electrical installations:

▪

Overload protection and separating protective devices

▪

Contact protection and additional insulation

▪

Ground connections

▪

Protection against vibrations, tensile stress, and corrosion

WARNING

Danger of electric shock

If the pump is not installed correctly, there is a risk of electric
shock.

➢

The electrical installation of the pump must be carried out

by a trained specialist who has relevant credentials.

«
...
8
9
10
11
12
...
»

Summary of Contents for FK 1100























Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands