KNECHT HV 203 Operating Instructions Manual Download Page 53 | Manualshive

Page: 53 / 70

background image

54

Figure 9-17

Aligning the knife on the grinding

belt

Figure 9-18

Tightening the grinding lever

1

9.1.8 Aligning the cutter knife on the wet-grinding belt

NOTE

The best grinding results are achieved when
the full width of the grinding belt is engaged
on the cutting edge of the knife.

Slightly loosen the grinding lever (9-16/1)
counter clockwise until the grinding plate with
the clamped knife can be moved.

Swivel the grinding plate with the clamped knife
until the full width of the grinding belt touches
the cutting edge.

Tighten the grinding lever (9-18/1) clockwise.

Hold the grinding plate with your second hand so
that it does not rotate when tightened.

Figure 9-16

Loosening the grinding lever

1

9. Operating the HV 262

«
...
51
52
53
54
55
...
»

Summary of Contents for HV 203







































































Reviews:

No comments

Related manuals for HV 203

Brand: JBM Pages: 36

Brand: Haybuster Pages: 176

Brand: Grizzly Pages: 2

Brand: Maestro Pages: 36

Brand: MACAP Pages: 24

Brand: TAKARA Pages: 20

Brand: Adler Europe Pages: 48

1375A - Grinder Angle 4 1/2 Small 6 Amp

Brand: Bosch Pages: 32

Brand: Bosch Pages: 129

Brand: Bosch Pages: 132

Brand: Bosch Pages: 39

Brand: Bosch Pages: 44

Brand: Bosch Pages: 36

Brand: Bosch Pages: 48

Brand: Bosch Pages: 164

Brand: Bosch Pages: 48

Brand: Bosch Pages: 52

Brand: Bosch Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands