KNECHT HV 203 Operating Instructions Manual Download Page 51 | Manualshive

Page: 51 / 70

background image

2

1

3

52

Turn clamping lever (9-10/1) to “Closed” position.

The knife is now locked.

Swivel the grinding plate with the clamped knife
forward to the grinding belt.

9.1.6 Basic function of the HV 262 locking mechanism

NOTE

The locking disc has several locking positions.
The first two positions are U-shaped, all
subsequent positions are V-shaped.

The two U-shaped locking positions are used to
adjust the knife on the grinding belt and to grind
the burr.

The V-shaped locking positions are used for
convex grinding of the knife.

0 = adjustment position (9-11/1)
1 = grinding position (9-11/2)
2 – 11 = convex grinding (9-11/3)

NOTE

Every grinding process is started with
adjustment position “0”.

1

Locking lever

2

Locking disc

3

Hand wheel

4

Star handle

Figure 9-10

Locking the knife on the grinding

plate

1

9. Operating the HV 262

Figure 9-11

Locking disc

Figure 9-12

Overview of locking mechanism

4

3

1

2

«
...
49
50
51
52
53
...
»

Summary of Contents for HV 203







































































Reviews:

No comments

Related manuals for HV 203

Brand: Baratza Pages: 21

Brand: Baratza Pages: 15

Brand: Parkside Pages: 197

Brand: Parkside Pages: 96

Brand: Parkside Pages: 110

Brand: Supera Pages: 7

Brand: Kawasaki-Plastics Pages: 4

Brand: Central Pneumatic Pages: 8

Brand: Mid Ocean Brands Pages: 5

Brand: Protool Pages: 148

Brand: Unit Pages: 20

Fatmax SFMCG400

Brand: Stanley Pages: 16

Brand: Jet Pages: 20

Brand: Proxxon Pages: 46

Brand: SUHNER Pages: 24

Brand: UZIN Pages: 36

Brand: Hobart Pages: 16

James Martin ZX595

Brand: Wahl Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands