background image

 

SmartMix Instructions V5350

 Installation 11

4.2  Installation in the LPG system

For use in a low-pressure gradient system, the SmartMix mixer is mounted 

according to figure 4.

Open-end wrench, size 10

Legend:

Metal screw fitting

Inlet to the pump B

Mixer lid

Mixer housing

Outlet to the column

Schematic diagram

Fig. 4: 

Installation SmartMix mixer in the LPG system 

1

5

2
3

4

1. 

Close the left connection in the LPG system with the metal screw 

fitting 

1

. Tighten the screw with the open-end wrench.

2. 

Connect the capillary leading to the pump by the right inlet to the 

pump 

2

 on the mixer lid 

3

.

3. 

Connect the capillary leading to the column with the outlet to the 

column 

5

.

4.3  Installation in the HPG system

For use in a high-pressure gradient system, the SmartMix mixer is mount-

ed according to figure 5.

Legend:

Inlet to the pump A

Inlet to the pump B

Mixer lid

Mixer housing

Outlet to the column

Schematic diagram

Fig. 5: 

Installation SmartMix mixer in the HPG system

1

5

2
3

4

1. 

Two pumps are used in the HPG system. Connect the Smart Mix mixer 

to the bottom pump.

2. 

Connect the capillaries from pump A and pump B with the two inlets 

to the pumps 

1

 and 

2

 on the mixer lid 

3

.

3. 

Connect the capillary leading to the column with the outlet to the 

column 

5

.

Tool

Summary of Contents for SmartMix























Reviews: