manualshive.com logo in svg

Knauer BlueShadow Series, Manual

Share
Download
Knauer BlueShadow Series Manual Download Page 47

48

Environmental protection

Cleaning and caring for the device

Note:

Risk of damage to the device if cleaning solution enters 
the device's interior! Only lighty moisten the cleaning 
cloth!

All smooth surfaces of the device can be cleaned with a mild, 
commercially available cleaning solution, or with isopropanol.

Environmental protection

Disposal

Drop the devices off at the local municipal waste facilities or 
send the devices back to the manufacturer where it will be dis-
posed of properly.

Decontamination

Contamination of devices with toxic, infectious or radio-active 
substances poses a hazard for all persons during operation, 
repair, sale and disposal of a device.

DANGER!

Danger caused by toxic, infectious, or radio-
active substances! A contaminated device must 
never be submitted for repairs, sold, or disposed 
of!

Contract a specialist company to decontaminate 
the device or perform the decontamination 
yourself if you have the required expertise!

All contaminated devices must be properly decontaminated by 
a specialist company or the operating company before they can 
be recommissioned, repaired, sold, or disposed of. 

All materials or fluids used for decontamination must be col-
lected separately and disposed of properly.

Storage

Ambient storage conditions for the device

Temperature range: 4–40 °C; 39.2–104 °F

Air humidity: Below 90 % humidity (non-condensing)

Summary of Contents for BlueShadow Series




























































Reviews:

No comments

Brands by name

Popular brands

Load more brands