manualshive.com logo in svg

Knauer BlueShadow Series, Manual

Share
Download
Knauer BlueShadow Series Manual Download Page 40

41

Operating the valves and valve drives

Connect valve drive to the devices 

Manager

 

or 

Interface Box

.

In order to send control signals to the valve drive, the 

Remote

 

terminal strip on the device's rear of the valve drive is connected 
to other devices, for example, a 

Manager

 or an 

Interface Box

.

Principle of the cabling

Connection of the relay with 

ground

Connection of the relay with a 

binary output

Fig. 37

Terminal strip: 

Remote

 and 

Interface Box IF2

The integrated circuit of the terminal strip 

Remote

 is designed 

as a MINI-WAGO connection in the construction of an open 
collector.

Connect flat ribbon cable 
to the connector strip

Steps

Figure

1. Place the connector strip 

(C) on a suitable surface.

2. Put the stylus (A) in the 

opening on the top of the 
connector strip and press 
downward.

3. Keep the stylus pressed 

down and insert the 
cable end (B) into the 
front of the connector 
strip.

4. Pull out the stylus.

5. Check whether the cables 

are tightly attached.

Fig. 36

Connecting the flat 
ribbon cable with the 
connector strip

A

B

C

Legend

A.  Back side of the 

interface device 

Interface Box IF2

B.  Back side of a valve 

drive

C. Terminal strip: 

Remote

 

 

 

 

Interface Box IF2 

A

B

C

Summary of Contents for BlueShadow Series




























































Reviews:

No comments

Brands by name

Popular brands

Load more brands