KMC Controls CSC 3000 Series Application Manual Download | Manualshive

Page: 12 / 15

background image

CSC-3000 Series Pneumatic VAV Reset Volume Controllers

12

Applications Guide, Rev G

Cooling with Heating P-E Switch

DA Thermostat, NO or NC Damper, and NC Heating P-E Switch

•  LO STAT = Min. Flow
•  HI STAT = Max. Flow
•  Reset Range = 8 to 13 psi

NC PE
Switches

• Stage 2 On with Decrease
• Stage 3 Off with Increase

• Stage 1 On with Decrease
• Stage 2 Off with Increase

• Stage 3 On with Decrease

• Stage 1 Off with Increase

•  LO STAT = Max. Flow
•  HI STAT = Min. Flow
•  Reset Range = 3 to 8 psi

NO PE
Switches

RA Thermostat, NO or NC Damper, and NO Heating P-E Switch

• Stage 2 On with Decrease
• Stage 3 Off with Increase

• Stage 1 On with Decrease
• Stage 2 Off with Increase

• Stage 3 On with Decrease

• Stage 1 Off with Increase

«
...
10
11
12
13
14
...
»

Summary of Contents for CSC 3000 Series
















Reviews:

No comments

Related manuals for CSC 3000 Series

Brand: ABB Pages: 139

Brand: ABB Pages: 28

Brand: ABB Pages: 59

Brand: CAME Pages: 32

Brand: Babybee Prams Pages: 21

Brand: TCS Basys Controls Pages: 2

Brand: Abicor Binzel Pages: 8

EtherNetIP ControlPlex CPC12EN

Brand: E-T-A Pages: 28

Brand: IDTECK Pages: 94

xPico 200 Series

Brand: Lantronix Pages: 7

Brand: Lantronix Pages: 3

Brand: Lantronix Pages: 15

Brand: Mackie Pages: 16

Brand: TANDBERG Pages: 47

Brand: Oceanic Pages: 11

Brand: Quinny Pages: 29

Brand: Quinny Pages: 60

Brand: Xilinx Pages: 52

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands