KMC Controls BAC-1xx63 Series Installation Manual Download

Page: 7 / 9

BAC-1xx63 Series (6 Relays, 3 Analog Outputs)

Installation Guide

STE-1451 Outside Air Temp. Sensor

STE-1416 Duct Averaging Temp. Sensor

MEP-5372/7252/7552/7852 Fail-Safe Actuators

XEE-6311-075 or XEE-6311-100 Transformer

IF BOTH RC AND RH TERMINALS ARE PRESENT:
WIRE RC TO SC 1-3 AND RH TO SC 4-6.

IF ONLY ONE “R” TERMINAL IS PRESENT:
WIRE BOTH SC 1-3 AND SC 4-6 TO R.

RTU 2H/2C LAYOUT

CSE-1102 Air Differential

Pressure Switch

NOTE: EITHER FAN STATUS (FST) OR

DISCHARGE AIR TEMP (DAT) CAN
BE USED ON IN2, BUT NOT BOTH.

STE-1402 Duct
Sensor, Type III

Roof Top Unit (RTU)—
1 or

2 Heat and 1 or 2 Cool

NOTE: Terminal connections and menus

reflect firmware version R1.3.0.4 or

later. (Relay 3 and 4 were swapped in

versions earlier than R0.0.0.0.)

Input Terminals

RTU Input Connections

BACnet Objects

IN4

Opt. Outside Air Temp. (OAT)*

AI4

IN3

Opt. Mixed Air Temp. (MAT)*

AI3

GND

Ground

IN2

Optional FST or DAT**

AI2

*When using optional Outside Air Damper, must also have MAT/OAT

inputs (typically 10K, Type III thermistors). Ensure pull-up resistor

switch positions are set properly—see Illustration 3 on page 2.

**Fan Status (FST) or Discharge Air Temperature (DAT) is an optional,

selectable input. Ensure pull-up resistor switch positions are set

properly (10K position) for the relay, switch, or Type III thermistor.

Output

Terminals

Typical Terminal

Codes

RTU Output Connections

(1 or 2 H and 1 or 2 C)

BACnet

Objects

Analog 9

Outside Air Damper (OAD/RTD)*

AO9

GND

Ground

(for analog output terminals 7–9)

Analog 8

(AO8)

Analog 7

(AO7)

Relay 6

(BO6)

SC 4–6

RH/R

24 VAC (for relay terminals 4–6)

Relay 5

Heat 2 (Optional)

BO5

Relay 4

Heat 1

BO4

Relay 3

Cool 2 (Optional)

BO3

SC 1–3

RC/R

24 VAC (for relay terminals 1–3)

Relay 2

Cool 1

BO2

Relay 1

Fan

BO1

*If optional Outside Air Damper is used, must also have MAT/OAT inputs.

APPLICATION

DEGREES SCALE: °F

APP:

OPT: 1H/1C
ADDITIONAL SETUP

ROOF TOP

ADDITIONAL SETUP

DAMPER

FAN
HUMIDITY
SENSORS

NOTE: Although typical terminal code letters are

shown, check the schematics of your unit for

wiring details.

NOTE: This was 2 Heat and 2 Cool in

firmware R1.3.04 and earlier.

Multistage was added later.

Summary of Contents for BAC-1xx63 Series










Search results

Summary of Contents for BAC-1xx63 Series

Reviews:

Related manuals for BAC-1xx63 Series

Brands by name

Popular brands

KMC Controls BAC-1xx63 Series, Installation Manual

Search results

Summary of Contents for BAC-1xx63 Series

Reviews:

Related manuals for BAC-1xx63 Series

Brands by name

Popular brands