manualshive.com logo in svg

KMB SMP133, Operating Manual

Share
Download
KMB SMP133 Operating Manual Download Page 8

SMY133-SMY134-SMP133 Operating Manual

2. Installation

2.1 Meaning of the symbols used on instrument

Warning – read operating manual !

AC – alternating voltage

DC – direct voltage

CE marking guarantees compliance with the European directives and regulations

The instrument must not be disposed of in the normal unsorted municipal waste 
stream

Basic insulation instrument (protection class I)

Double or reinforced insulation instrument (protection class II)

2.2 Physical

The instrument is built in a plastic box to be installed in a distribution board panel. As a rule, the panel 
is a part of a switchboard door - then the installation must be such that the switchboard door can be 
closed under all conditions of use. In any case, it must be ensured that only the front panel of the 
instrument is accessible to laypersons. Therefore, if the switchgear is located in an area accessible to 
laypersons, the switchgear door or panel must only be opened by means of a tool, or the door must be
locked.

8

Fig. 2.1a : Panel Mounting

switchboard outer side
accessible to laymen
minimum protection IP40

switchboard inner side
inaccessible to laymen
protection IP20 or lower

Summary of Contents for SMP133





















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands