KLS Martin Independant IDP 401 Mounting Instructions Download Page 53

Page: 53 / 116

Mounting Instructions

Suspension Arm Systems Independant

Revision 1

7.2

Pre-assembly: Mounting the Longer Ceiling Tube on the

Extension Arm

7.2.1

Overview of the Components in this Section

The ceiling tube

shown in the illustration is

mounted to the extension arm

(Single

or Duo).
For reasons of simplification, the illustration
shows the extension arm without the pre-
installed cables.
The installation is described in the following
sections and differs depending on the version.

•

Observe the different lengths and
number of fastening screws for the
different versions.

Fig. 7-8:

Overview of the components in this section

Summary of Contents for Independant IDP 401





















































































































Search results

Summary of Contents for Independant IDP 401

Reviews:

Related manuals for Independant IDP 401

Brands by name

Popular brands

KLS Martin Independant IDP 401, Mounting Instructions

Search results

Summary of Contents for Independant IDP 401

Reviews:

Related manuals for Independant IDP 401

Brands by name

Popular brands