klover SOFT 100, Installation, Use And Maintenance, Useful Advice

Page: 50 / 57

45
SOFT 80, SOFT 100 PELLET-BURNING STOVE EN - Rev. 1.0
“FACTORY SETTINGS” parameters - Model S80 (L09_161018)
Parameter Menu level Description Display wording Measurement Value field
Database
o9
Pr01 M10 – 05 – 01 Ignition cycle maximum time START TIME Minutes 5 – 25 18
Pr02 M10 – 05 – 02 Time for flame stabilisation after ignition FL. LIGHT TIME Minutes 0 – 15 9
Pr03 M10 – 05 – 03 Time interval between the two brazier cleaning cycles CADENCE CLEANING Minutes 3 – 240 60
Pr04 M10 – 05 – 04 Auger gearmotor ON time in ignition phase AUGER START Seconds 0.1 – 8.0 0,8
Pr05 M10 – 05 – 05 Auger gearmotor ON time during the stabilisation phase AUGER FL. LIGHT Seconds 0.1 – 8.0 1,2
Pr06 M10 – 05 – 06 Auger gearmotor ON time in power 1 work phase AUGER POWER 1 Seconds 0.1 – 8.0 1,8
Pr07 M10 – 05 – 07 Auger gearmotor ON time in power 2 work phase AUGER POWER 2 Seconds 0.1 – 8.0 2,4
Pr08 M10 – 05 – 08 Auger gearmotor ON time in power 3 work phase AUGER POWER 3 Seconds 0.1 – 8.0 3,0
Pr09 M10 – 05 – 09 Auger gearmotor ON time in power 4 work phase AUGER POWER 4 Seconds 0.1 – 8.0 3,8
Pr10 M10 – 05 – 10 Auger gearmotor ON time in power 5 work phase AUGER POWER 5 Seconds 0.1 – 8.0 4,5
Pr11 M10 – 05 – 11 Time after which the alarm is signalled following an anomaly ALARMS DELAY Seconds 0 – 120 90
Pr12 M10 – 05 – 12 Brazier cleaning duration CLEANING DURATION Seconds 0 – 120 60
Pr13 M10 – 05 – 13 Minimum temperature of the combustion chamber in order to consider the
appliance on
MINIMUM THRESHOLD °C 70 – 280 180
Pr14 M10 – 05 – 14 Maximum temperature of the combustion chamber
MAXIMUM
THRESHOLD
°C 200 – 880 800
Pr15 M10 – 05 – 15 Combustion chamber temperature threshold for starting the air
exchangers
BLOWER THRESHOLD °C 100 – 720 180
Pr16 M10 – 05 – 16 Smoke extraction speed in ignition phase SMOKE SP. START Rpm 500 – 2800 2100
Pr17 M10 – 05 – 17 Smoke extraction speed in start phase SMOKE SP. FL. LIGHT Rpm 500 – 2800 2000
Pr18 M10 – 05 – 18 Smoke extraction speed in power 1 work phase SMOKE SPEED P1 Rpm 500 – 2800 1550
Pr19 M10 – 05 – 19 Smoke extraction speed in power 2 work phase SMOKE SPEED P2 Rpm 500 – 2800 1700
Pr20 M10 – 05 – 20 Smoke extraction speed in power 3 work phase SMOKE SPEED P3 Rpm 500 – 2800 1900
Pr21 M10 – 05 – 21 Smoke extraction speed in power 4 work phase SMOKE SPEED P4 Rpm 500 – 2800 2100
Pr22 M10 – 05 – 22 Smoke extraction speed in power 5 work phase SMOKE SPEED P5 Rpm 500 – 2800 2200
Pr23 M10 – 05 – 23 Heat exchanger 1 (primary) speed in power 1 work phase AIR SPEED P.1 Volt 65 – 225 150
Pr24 M10 – 05 – 24 Heat exchanger 1 (primary) speed in power 2 work phase AIR SPEED P.2 Volt 65 – 225 160
Pr25 M10 – 05 – 25 Heat exchanger 1 (primary) speed in power 3 work phase AIR SPEED P.3 Volt 65 – 225 170
Pr26 M10 – 05 – 26 Heat exchanger 1 (primary) speed in power 4 work phase AIR SPEED P.4 Volt 65 – 225 180
Pr27 M10 – 05 – 27 Heat exchanger 1 (primary) speed in power 5 work phase AIR SPEED P.5 Volt 65 – 225 195
Pr28 M10 – 05 – 28 Combustion chamber temperature threshold for considering the device off THRESHOLD OFF °C 50 – 250 170
Pr29 M10 – 05 – 29 Smoke extraction speed in the brazier cleaning phase SMOKE SP. CLEANING Rpm 700 – 2800 2800
Pr30 M10 – 05 – 30 Auger gearmotor ON time in the cleaning phase AUGER CLEANING Seconds 0.0 – 8.0 1,0
Pr31 M10 – 05 – 31 Enabling of a primary room temperature probe connected to the board
MOTHERBOARD
PROBE
On – Off On – Off Off
Pr32 M10 – 05 – 32 Pre-heating time PREHEAT TIME Seconds 0 – 250 0
Pr33 M10 – 05 – 33 PELLET CRUISE CONTROL modulation threshold CRUISE THRESHOLD °C 120 – 880 540
Pr34 M10 – 05 – 34 Temperature delta on PELLET CRUISE CONTROL modulation threshold CRUISE DELTA °C 20 – 60 40
Pr35 M10 – 05 – 35 PELLET CRUISE CONTROL modulation time CRUISE TIME Minutes 1 – 10 3
Pr36 M10 – 05 – 36 Time after which the intervention of the Technical Assistance Centre is
requested
SERVICE HOURS Hours
Off
260 – 2800
2000
“RELAX SETTINGS” parameters - Model S80 (L09_161018)
Parameter Menu level Description Display wording Measurement Value field
Database
o9
Pr150 M10 – 10 – 01
Heat exchanger 1 (primary) speed during the work phase with “RELAX
FUNCTION” enabled
RELAX AIR SPEED Volt
Off
65 – 225
Off
Pr151 M10 – 10 – 02 “RELAX FUNCTION” activation time RELAX TIME Minutes
30 – 254
On
30