Kleinn Air Horns X3-KIT Installation Manual Download | Manualshive

Page: 21 / 40

background image

X3-KIT

Installation and Operation Manual

Go to Table of Contents

PG 21/40

REV: BETA (4/25/2019)

8.3.

Remove Driver side Rear Fender

8.3.1.

Repeat previous steps for Passenger Fender removal.

8.4.

Air Tank Brackets - Installation

8.4.1.

Gather Brackets X3-201, X3-202, X3-203 and X3-204 (2)

8.4.2.

On passenger side of vehicle, remove two (2) bolts holding rear deck; as shown below. Do not discard
large bolt, as it will be re-used. Smaller bolt (i.e., front bolt) will be replaced.

Figure 6

–

Air Tank Bracket Mounting Locations (side view)

Figure 7

–

Air Tank Bracket Mounting Locations (top view)

FRON

T

Front Bolt

FRONT

Rear Deck bolt

Front Deck bolt

Chassis Tube

«
...
19
20
21
22
23
...
»

Summary of Contents for X3-KIT









































Reviews:

No comments

Related manuals for X3-KIT

BTL7-S5 B-M Series

Brand: Balluff Pages: 14

BML-S1G0 7 M5E 0 Series

Brand: Balluff Pages: 194

Action Replay DSi

Brand: Datel Pages: 2

Brand: IFM Electronic Pages: 16

Brand: IFM Electronic Pages: 6

Brand: LAZER Pages: 19

Audio Interface Conectiv

Brand: M-Audio Pages: 18

Tinker PIZZA-BOX/ THERMO-BOX

Brand: RIESE & MULLER Pages: 4

Brand: R&G Pages: 10

Brand: Focusrite Pages: 29

Brand: Maserati Pages: 210

Brand: OnStar Pages: 22

Brand: Lamp Pages: 2

Quattroporte Automatic

Brand: Maserati Pages: 272

Brand: RBR Pages: 13

Brand: PCB Piezotronics Pages: 9

Brand: NATIVE UNION Pages: 3

Solar Shade 200

Brand: Dometic Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands