Kleinn Air Horns CANX3-KIT Installation Manual Download | Manualshive

Page: 21 / 44

background image

CANX3-KIT

Installation and Operation Manual

Go to Table of Contents

PG 21/44

REV: A (9/4/2020)

8.3.

Remove Driver side Rear Fender

8.3.1.

Repeat previous steps for Passenger Fender removal.

8.4.

Air Tank Brackets - Installation

8.4.1.

Gather Brackets X3-201, X3-202, X3-203 and X3-204 (2)

8.4.2.

On passenger side of vehicle, remove two (2) bolts holding Rack; as shown below. Do not discard large
bolt, as it will be re-used. Smaller bolt (i.e., front bolt) will be replaced.

Figure 6

–

Air Tank Bracket Mounting Locations (side view)

Figure 7

–

Air Tank Bracket Mounting Locations (top view)

FRONT

Front Bolt

FRONT

Rack Rear Bolt

Rack Front Bolt

Chassis Tube

«
...
19
20
21
22
23
...
»

Summary of Contents for CANX3-KIT













































Reviews:

No comments

Related manuals for CANX3-KIT

Brand: Velleman Pages: 12

Yeti SCORE Trophy Truck

Brand: Axial Pages: 15

driftspec TT-02D

Brand: Tamiya Pages: 25

Brand: Jamara Pages: 20

Brand: 3Racing Pages: 30

Brand: Tyco R/C Pages: 4

Nissan 300ZX IMSA-GTO

Brand: Tamiya Pages: 20

Revo 5304 Platinum Edition 2008

Brand: Traxxas Pages: 20

Brand: Lenox Pages: 12

Survolt BX10 2.0 Sport

Brand: Hobbytech Pages: 40

Brand: AE Pages: 4

1:10 EP Truggy Rockhard BL RtR

Brand: Reely Pages: 31

Cucciolo Acquarello

Brand: Peg-Perego Pages: 16

Case IH Magnum Tractor

Brand: Peg-Perego Pages: 29

Team McDonalds Nascar Rider

Brand: Fisher-Price Pages: 6

Brand: Traxxas Pages: 2

4 Nitro Tec 4804

Brand: Traxxas Pages: 19

Brand: TO DO Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands