Klein Marine Systems, Inc. MA-X VIEW 600, Operation And Maintenance Manual

Page: 8 / 128

viii
MA-X View 600 Sonar System Operations and Maintenance Manual P/N 11210097, Rev. 00
List of Figures
Figure 1-1: Towfish . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
Figure 1-2: SP-III TPU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
Figure 1-3:
Rack Mount TPU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5
Figure 1-4: SonarPro Workstation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6
Figure 3-1: SP-III TPU Side Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6
Figure 3-2: Rack Mount TPU Back Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-8
Figure 3-3:
SonarPro Workstation Back Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10
Figure 3-4: Rack Mount TPU Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-16
Figure 3-5: SonarPro Workstation Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-19
Figure 3-6: Towfish with Gap-filling Transducers Deployed . . . . . . . . . . . . . . . . . . . . 3-23
Figure 4-1:
Loosening the Tail Cone Retaining Bolt . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3
Figure 4-2: Removing the Tail Cone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4
Figure 4-3: Tail Cone Removed from the Towfish Housing . . . . . . . . . . . . . . . . . . . . . . 4-4
Figure 4-4: Removing the Nose Cone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5
Figure 4-5:
Disconnecting the Transducer Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5
Figure 4-6: Tightening the Locking Screws in the Towfish Housing Forward End
Cap
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6
Figure 4-7: Screwing the Tail Cone Retaining Bolt into the Forward End Cap . . . . . . . 4-6
Figure 4-8: Pulling the Forward End Cap out of the Towfish Housing . . . . . . . . . . . . . 4-7
Figure 4-9:
Forward End Cap Removed from the Towfish Housing . . . . . . . . . . . . . . . 4-7
Figure 4-10: Tightening the Locking Screws in the Towfish Housing Aft End Cap . . . . . 4-8
Figure 4-11: Pulling the Electronics Chassis out of the Towfish Housing . . . . . . . . . . . . 4-8
Figure 4-12: Transition Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-9
Figure 4-13:
Aligning the Locking Screws before Inserting the Forward End Cap . . . . 4-10
Figure 4-14: Aligning the Locator Pin in the Nose Cone with the Slot in the Towfish
Housing
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-10
Figure 4-15: The Three Screws Securing the Skid Plate to the Towfish . . . . . . . . . . . . . 4-11
Figure 4-16: Removing the Three Screws Securing the Skid Plate to the Towfish . . . . . 4-11