Klein Marine Systems, Inc. HYDROCHART 3500 Operation And Maintenance Manual Download | Manualshive

Page: 67 / 86

background image

B-1

APPENDIX B: C

ONFIGURING

AND

U

PDATING

THE

S

ONAR

H

EAD

U

NIT

The Sonar Head Unit is configured at the factory. However, should changes be
required, configuring and updating the Sonar Head Unit can be performed using
Linux Updater. This program is automatically installed when installing SonarPro
12.1 and can be used to query or change the Sonar Head Unit IP address, edit the
startup file of the Sonar Head Unit, or download and install software updates to the
Sonar Head Unit.

B.1 Querying or Changing the Sonar Head Unit IP

Address

To query or change the Sonar Head Unit IP address:

1.

Turn on the PC and wait for the Windows desktop to appear.

2.

Turn on the TIU by pressing the ON/OFF switch.

3.

Start Linux TPU Updater

by double-clicking the Linux TPU Updater icon

on the Windows desktop

.

The

Klein Linux TPU Updater

dialog box opens:

4.

Connect a Null Modem cable from an available RS-232 serial port on the PC to
the NAV connector on the TIU.

5.

Click

Read TPU IP Address

.

The

Select RS-232 Port

dialog box opens:

«
...
65
66
67
68
69
...
»

Summary of Contents for HYDROCHART 3500























































































Reviews:

No comments

Related manuals for HYDROCHART 3500

Brand: Furuno Pages: 74

Brand: Lowrance Pages: 192

Strata 128 Portable

Brand: Eagle Pages: 64

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands