Klein Marine Systems, Inc. HYDROCHART 3500 Operation And Maintenance Manual Download | Manualshive

Page: 17 / 86

background image

1-1

CHAPTER 1: O

VERVIEW

The HydroChart 3500 Sonar System is a lightweight, compact, one person
deployable shallow water hydrographic survey system which makes use of Klein
Marine Systems proprietary wideband "chirp" technology to simultaneously
collect IHO (International Hydrographic Organization) quality bathymetry and co-
registered, geo-referenced, high resolution side scan sonar data.

1.1

Key Features

The HydroChart 3500 Sonar System delivers the following key features:

• Compact, portable and lightweight

• Easy setup, deployment and operation by one person

• Long range high resolution imaging at 455 kHz

• High resolution IHO quality swath bathymetry

• Co-registered, geo-referenced swath bathymetry and side scan data

• Bathymetry coverage up to 12 times altitude

• Support for an optional motion reference unit (MRU)

• Support for an optional sound velocity sensor

• Ruggedly constructed

• Operates with Klein Marine Systems SonarPro data acquisition and display

software

1.2

Applications

Major applications for the HydroChart Sonar System include the following:

• Shallow water hydrographic survey

• Geophysical survey

• Port and harbor security

• Dredging and salvage operation

• Rapid littoral area assessment

«
...
15
16
17
18
19
...
»

Summary of Contents for HYDROCHART 3500























































































Reviews:

No comments

Related manuals for HYDROCHART 3500

Sonar UI SeaBat T Series

Brand: Teledyne Pages: 2

Brand: Eagle Pages: 168

Brand: Simrad Pages: 154

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands