KLAXON Mobility Gmbh – ENG
KLICK Electric User's Manual (ENG) - rev.6.1 of 15.06.2018
20
•
After turning on the display, the initial screen shows (in number 3) the partial distance (TRIP) of the device in use.
•
Press the “
M
” button once to enter the second screen. It will show the total distance (ODO).
•
Press again the “
M
” button once to enter the third screen. It will display the maximum speed reached (MAX).
•
Press again the “
M
” button once to enter the fourth screen. It will show the average speed (AVG).
•
Press again the “
M
” button once to enter the fifth screen. It will show the approximate distance that can be covered based
on the current battery level (RANGE); this estimate varies according to the maximum speed level selected.
•
Press again twice the “
M
” button to display the total time the device has been on (TIME).
C. Resetting data
•
Once the display has been turned on, press the “
+
” and “
-
“ buttons together for 5 seconds to enter the MENU. Several
options will be displayed.
•
Use the “
+
” and “
-
“ buttons to navigate within the MENU and select DISPLAY SETTING; press the “
M
” button to enter the
selected submenu.
•
Once in the submenu, use the “
+
” and “
-
“ buttons to select TRIP RESET and press the “
M
” button to enter.
•
Press the “
+
” button to move from NO to YES; press the “
M
” button to confirm the selected option.
•
Press the “
+
” and “
-
“ buttons together for 5 seconds to exit the MENU and go back to the main screen.
D. Screen Backlighting
•
Hold the “
+
” button for 5 seconds to turn on the screen backlight.
•
To turn off the backlight, press the “
+
” button for 5 seconds again.
•
When the device is turned off, the light is also automatically switched off.
CAUTION: this procedure must also be used to turn on and off the front LED light connected to the MINI and FLY MINI batteries,
included in the ELECTRIC MINI CARBON version.
E. Speed Hold Function
•
Press the “
-
“ button for 5 seconds to turn on the speed hold function. This function accelerates the device up to a speed of
4.5 km/h and holds it as long as the button is pressed.
•
When the button is released, the device instantly stops accelerating.
DANGER
Every action and/or tampering of the display to change performance and KLICK’s security is strictly
prohibited. The sole and only actions possible are those specified in paragraph 16.2 of this User’s Manual.
NOTE:
For further information on the display, see
www.klaxon-klick.com
or contact an authorised KLAXON dealer.
16.3 USE
Figure 61 shows the Standard handlebar of the Klick device and it identifies the elements that make it up (listed below).
1.
Handlebar
2.
Acceleration control
3.
Display
4.
Brake lever
Once the device has been installed, the display has been turned on and a speed has been selected, use the accelerator control to
make the device start to move (Figure 31.1). To stop the device, use the brake lever. The KLICK brake is equipped with an additional
safety device which deactivates the motor when the lever is operated (Figure 31.2).
The brake lever, the accelerator control and the display can be installed either on the left or on the right side of the handlebar
according to user's preference.
DANGER
For installation and positioning of controls (display, accelerator control, brake lever), contact an
authorised KLAXON service centre.
DANGER
At each restart pay maximum attention, before accelerating, to check if forward or reverse
operation is currently selected, especially when close to obstacles, drop-offs and any other kind of
danger.
DANGER
If obstacles, drop-offs and dangers are too close to be safe, turn off the KLICK device and manually
move the wheelchair to a safe place.
16.4 TURNING OFF AND RELEASING FROM THE WHEELCHAIR
To perform the operation properly, carefully follow the following instructions.
•
Stop the wheelchair on a flat surface.
•
Apply the brake on the wheelchair.
•
Turn off the display by pressing and holding the “
M
” button for 5 seconds.