Strona 11 z 17
rev. 1.0.1
USER MANUAL
:
KIVOS KD300
MULTIPURPOSE WIRELESS VIDEO DOOR PHONE INTERCOM SYSTEM
WITH MULTI MONITOR
www.elmic.pl
,
elmic@elmic.pl
Unlock: in “
OK
” on-state mode -
》
press “
” unlock key -
》
after successful unlocking, it shows unlock icon.
Photo: in “
OK
” on-state mode -
》
press “
” photo taking key -
》
one press one photo, the photos will be stored in TF
card.
Video: in “
OK
” on-state mode -
》
press “
”video taking key -
》
start taking video -
》
press “
” video taking key
again to stop, the videos will be stored in TF card.
Exit: in “
OK
” on-state mode -
》
press “
OK
” key (in monitor mode -
》
press “Exit” )the unit turns into standby mode with
a sound of “Beep”.
Automatic video: if nobody answers the call in 5 seconds, indoor monitor starts taking video automatically (Default
is automatic video. If setting is manual video, once connected, the indoor unit will take video manually) till being
stopped or max. taking time.
7.
Indoor Monitor CALL Outdoor Unit (Monitoring)
In standby mode, press “
” monitor key on indoor monitor to monitor call. In this mode, the red LED lights up.
If outdoor unit receives signal in 5 seconds, then it connects to indoor monitor, indoor machine turns into normal monitor
mode and shows image and speaks voice of outside. There is no voice speaking for outdoor unit. If outdoor unit doesn’t
receive signal in 5 seconds, then it shows “User not online” and exits monitor calling mode automatically and turns into
standby mode.
Two sets of outdoor units (Code connected successfully):
Press “
” monitor key on indoor monitor to turn into monitor selection menu -
》
press “
↑
/
↓
” key to choose code
of outdoor units -
》
press “
OK
” to turn into monitoring call mode, red LED lights up (During selection, press “Exit” to turn
into standby mode ).
Intercom: in monitor mode, red LED lights up, there is voice speaking for indoor monitor but not for outdoor unit -
》
press “
OK
” to turn into both-way communication, red LED shuts down -
》
press “
” monitor key again to turn back
to one way voice monitor mode. (One or both-way voice could be changed over repeatedly). Intercom time
is 90 seconds and shall be timed again after changing over.
Unlock: in “
OK
” on-state mode -
》
press “
” unlock key -
》
after successful unlocking, it shows unlock icon.
Photo: in monitor mode -
》
press “
” photo taking key -
》
one press one photo, the photos will be stored in TF card.
Video: in monitor mode -
》
press “
”video taking key -
》
start taking video -
》
press “
” video taking key again
to stop, the videos will be stored in TF card.
End: in monitor mode -
》
press “
EXIT
” key -
》
end monitor and turn back to standby mode. (In intercom mode, press
“
OK
” to hang off.)
Note
: in monitor mode, red LED lights up, in intercom mode, red LED shuts down.
8.
Indoor Monitor CALL Indoor Monitor (Intercom)
(Only can realize when there are 2 and more indoor monitors.)
In standby mode, if there are only two indoor monitors in system, press “
OK
” to call another indoor monitor.
In standby mode, if there are three indoor monitors in system, press “
↑
” to call small code indoor monitor; press “
↓
”
to call large code indoor monitor;
If the CALLED indoor monitor doesn’t receive the signal in 4 seconds, the CALL monitor shows “User not online”,
it turns back to standby mode with a sound of “Beep”.
If the CALLED indoor monitor receives the signal, two monitors play music, green LED lights up.
If the CALLED indoor monitor doesn’t reply, the monitors turn into standby mode after 30seconds.
If the CALLED indoor monitor replies by pressing “
Ok
”, music stops, red LED shuts down, green LED lights up to both
of the monitors, and both monitors turn into intercom mode, communication time is max. 90seconds.
The CALL indoor monitor has initiative hang up function.
During communication, if any end in the communication presses “
OK
”, then both two ends hang up with a sound
of “Beep” and turn to standby mode.