22
Additional Features
Door Ajar Alarm
The Door Ajar Alarm feature sounds an alarm when the
refrigerator door(s) or freezer drawer is open for 5 minutes and
cooling is turned on. The alarm will repeat every 2 minutes. Close
all doors and drawer to turn it off.
NOTE:
To mute the audible alarm while keeping the doors open,
such as while cleaning the inside of the refrigerator, touch any
button on the control panel. The alarm sound will be temporarily
turned off, but the Door Ajar icon will still be displayed on the
dispenser control panel.
Water and Ice Dispensers
IMPORTANT:
■
Allow 3 hours for the refrigerator to cool down and chill water.
■
Allow 24 hours to produce the first batch of ice. Discard the
first 3 batches of ice produced.
■
The dispensing system will not operate if the left-hand
refrigerator door is open.
!
Calibration
!
Door
Ajar
!
Replace
Filter
!
"#$#!
!
%&#'#(')!"#$#
!
!
Order Filter
!
a1 oz = b1 L
!
a2 oz = b2 L
!
a3 oz =
b3 L
!
Dispense
!
Flush the Water System
Air in the water dispensing system can cause the water dispenser
to drip. After connecting the refrigerator to a water source or
replacing the water filter, flush the water system.
Flushing the water dispensing system forces air from the water
line and filter and prepares the water filter for use. Additional
flushing may be required in some households.
NOTE:
As air is cleared from the system, water may spurt out of
the dispenser.
1.
Using a sturdy container, depress and hold the water
dispenser paddle for 5 seconds.
Calibrate Measured Fill
Household water pressure may affect the accuracy of the
Measured Fill feature. So, for optimum performance of your
water dispenser, you must first calibrate Measured Fill.
IMPORTANT:
■
Flush the water system before calibrating Measured Fill.
■
For best results, calibration should be performed when water
is not being used in the house.
1.
Place a sturdy measuring cup (1-cup [237 mL] size) on the
dispenser tray centered in front of the ice/water dispenser
paddle.
NOTE:
Depending on your model, a measuring cup may be
provided.
!
Calibration
!
Door
Ajar
!
Replace
Filter
!
"#$#!
!
%&#'#(')!"#$#
!
!
Order Filter
!
a1 oz = b1 L
!
a2 oz = b2 L
!
a3 oz =
b3 L
!
Dispense
!
A. Water dispenser paddle
B. Ice dispenser paddle
C. Measuring cup (1 cup)
Ensure that you do not have any Measured Fill preset
selected.
2.
Touch and hold the Measured Fill button for 3 seconds to
enter into Calibration mode. The Calibration and Measured
Fill icons will illuminate and remain lit while the Measured Fill
feature is being calibrated.
NOTE:
You may touch MEASURED FILL to exit at any time in
Calibration mode. The Calibration icon will disappear and the
display will return to the Home screen.
3.
Press and hold the water dispenser paddle, as needed, to
dispense water to the 1-cup fill line in the measuring cup.
NOTE:
If overfilling or spilling occurs, discard the water and
restart the calibration process.
4.
When 1 cup of water has been correctly dispensed into
the measuring cup, touch MEASURED FILL to confirm the
calibration.
5.
When Measured Fill calibration has been confirmed, the
Calibration icon will disappear and the display will return
to the home screen.
B
A
A. Water dispenser paddle
B. Ice dispenser paddle
B
A
C
Lighting the Refrigerator
The refrigerator has an interior light that comes on any time the
door is opened.
NOTE:
The light is an LED which does not need to be replaced.
If the LED does not illuminate when the door is opened, call
Service to replace the light. See “Assistance or Service” in
“Warranty” section for contact information.
2.
Release the dispenser paddle for 5 seconds. Repeat steps
1 and 2 until water begins to flow.
3.
Once water begins to flow, continue depressing and releasing
the dispenser pad (5 seconds on, 5 seconds off) until a total
of 3 gal (12 L) has been dispensed.
