background image

25

WARRANTY

Warranty

© 2019 Kirsch Custom Window Coverings. All rights reserved. All trademarks used herein are the property of Kirsch or their respective owners. 09/19

Kirsch® is proud to extend a 10-year limited warranty on all Kirsch Custom Window Covering products. This is part 
of our commitment to providing the highest quality products, which has been our continued tradition since 1907.

COVERED

by a 10-Year  

Limited Warranty

•  Kirsch Custom Window Covering products are 

covered for defects in materials, workmanship 
or failure to operate for 10 years from the 
date of purchase (unless a shorter period is 
provided below), provided that the original retail 
purchaser continues to own the product.

• All internal mechanisms.
• Fabric delamination.
•  Components, brackets and operational cords.
•  Repairs and/or replacements will be made with 

like or similar parts or products. Fabric style, color 
or components may vary depending on original 
purchase date. 

•  Kirsch automation components are covered for 

5 years from the date of purchase.

NOT COVERED

by a 10-Year  

Limited Warranty

•  Any conditions caused by normal wear and tear.
•  Abuse, accidents, misuse or alterations to the 

product.

•  Exposure to the elements (sun damage, wind, 

water/moisture, salt air) and discoloration or 
fading over time.

•  Normal maintenance associated with motors  

and related accessories including, but not limited 
to, recharging and replacement of batteries.

•  Failure to follow our instructions with respect  

to measurement, proper installation, cleaning  
or maintenance.

•  Shipping charges, cost of removal and 

reinstallation.

 

Kirsch (or its licensed fabricator/distributor) will repair or replace the product or components found to be defective.

TO OBTAIN WARRANTY SERVICE:

• Contact your original dealer (place of purchase) for warranty assistance.
•  Contact Kirsch at 844-KIRSCH2 (844-547-7242) for technical support, certain parts free of charge, for 

assistance in obtaining warranty service or for further explanation of our warranty.

NOTE:

 In no event shall Kirsch or its licensed fabricator/distributor be liable or responsible for incidental or 

consequential damages or for any other indirect damage, loss, cost or expense. Some states do not allow the 
exclusion or limitation of incidental or consequential damages, so the above exclusion or limitation may not apply to 
you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

10-Year Limited Warranty

Summary of Contents for Cellular Shade Collection



























Reviews: