background image

17

INSTALLATION

DECLARATIONS

U.S. Radio Frequency FCC Compliance

FCC ID information is located on top of the blind’s headrail.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:  

(1) This device may not cause harmful interference, and  

(2) This device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are 

designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio 

frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there 

is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, 

which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following 

measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) 

Exposure Guidelines. This equipment should be installed and operated keeping the radiator at least 20 cm or more away from person’s body. RF Exposure 

requirements are met when installed in mobile equipment. This module cannot be installed in portable equipment without further testing and a change to 

FCC’s grant of authorization. 

.

Summary of Contents for Alternative Wood Blinds Series




















Reviews: