manualshive.com logo in svg

Kirby Morgan M-48 SuperMask, User Manual

Share
Download
Kirby Morgan M-48 SuperMask User Manual Download Page 46

Accessories/Spares

46

 

© MMXXI Kirby Morgan Dive Systems, Inc. All rights reserved. Document # 210902001

Mask Bag P/N 800-905

A convenient Mask Bag is available for stor-
age and transportation of the mask, Pod, and 
regulators.

KMDSI Mouthpiece 
P/N 810-022L

This is the mouthpiece that 
comes in the pod when equipped 
with Kirby Morgan’s Balanced 
SCUBA regulator. If you need a 
replacement, or just a spare on 
hand, ask for mouthpiece P/N 
810-022L.

SCUBA Pod Assembly 
with Balanced SCUBA 
Regulator P/N 200-130

This SCUBA pod includes the lat-
est and most advanced SCUBA 
regulator in our product line, the 
Balanced SCUBA regulator. The 
flexible shroud, gives the diver 
a wider activation area over tra-
ditional purge button systems. 

This shroud also incorporates a wide exhaust body that aids in lowering 
the exhalation effort and deflects exhaust bubbles away from the diver’s 
field of vision.

The SCUBA pod with the Balanced SCUBA regulator comes standard with 
a balanced water purge tube which, unlike the tilt to purge system, enables 
the diver to clear and dewater the pod hands free.

When using P/N 200-130 as spare regulator, divers using the SuperMask

®

 

/MOD-1 modular full face mask will have the benefit of securing their back 
up, bailout or decompression gas directly to the mask with the continued 
benefits of the modular full face mask.

Summary of Contents for M-48 SuperMask

























































Reviews:

No comments

Brands by name

Popular brands

Load more brands