manualshive.com logo in svg

Kirby Morgan M-48 SuperMask, User Manual

Share
Download
Kirby Morgan M-48 SuperMask User Manual Download Page 24

Pre-Dive

24

 

© MMXXI Kirby Morgan Dive Systems, Inc. All rights reserved. Document # 210902001

pulled through the buckle assembly and clear of the mask. This will lower 
the chance of losing the strap keeper and ensure correct orientation into 
the strap groove. Remember to remove the keepers before attempting to 
reinstall the straps onto the mask. Lift up on the tab found at the edge 
of the buckle assembly while simultaneously pulling the strap leg until it 
is completely fed through the assembly and clear of the mask. Repeat 
process for the remaining three straps.

Installation of the Mask Strap on Mask Frame

Orient the mask strap so that the circular junction of the mask strap will 
be positioned at the back of the diver’s head, with the smooth side of the 
harness facing out and the ribs on the strap legs against the head. Begin 
with one of the top straps and feed the strap through the adjustment buckle 
by lifting up on the tab of the buckle assembly. The strap keeper groove 
will appear after the tapered leading edge followed by the resistance ribs. 
The resistance ribs will face the head or hood and the smooth side faces 
away from the head or hood. This will provide correct threading through 
the assembly. Reinstall the strap keeper into strap groove. Repeat process 
for the remaining three straps.

NOTE

The strap keepers prevent the straps from coming free from the 
buckles and must be in place prior to diving.

Cleaning the Face Port and Interior Surfaces

The M-48 SuperMask

®

 frame and pod components are made of high im-

pact plastic. The flexible face seal and pod skirts are molded of high grade 
injection molded liquid silicone.

Ensure that the viewing lenses are clear and clean. Fogging can be elimi-
nated or reduced by thoroughly cleaning the interior of the lens and ap-
plying a good quality anti-fog solution. Follow the manufacturer’s recom-
mendations for use.

If commercial anti-fog solution is unavailable, 

1/2

 a drop per lens of liquid 

dish washing soap or liquid hand soap can be used. Apply the small dab, 
smearing a thin film on the inside of the lens and let dry. Follow with a 
light buff with a soft cloth allowing a slight residue of soap film to remain 
on the face port to inhibit fogging.

Summary of Contents for M-48 SuperMask

























































Reviews:

No comments

Brands by name

Popular brands

Load more brands