
REFRIGERATOR CONTROLLER Model REF-DF-SM Version 4.2
DESCRIPTION
REF-DF-SM Version 4.2
is a compact controller for refrigerator’s control with defrost. Via one
PTC
sensor, it controls room’s temperatures with temperature range -19÷+99°C
(-2÷+210°F). It has defrost control and three relays (compressor, water level, ON-OFF). Also it has an OFF state, in which all relays are OFF and it has one input for level
control and one input for open door. The controller has a serial input and can connect to the
KIOUR
CAMIN
modbus network for full monitoring and data logging of the device.
INDICATIONS AND BUTTON OPERATIONS
PROGRAMMING THE PARAMETERS
By pressing at the same time
[
SET
] and [
], [
] we access the parameters menu.
The first parameter “
SP”
is displayed and with [
], [
] we scroll into the parameters with the order they appear to parameters table below .
By pressing [
SET
] the value of the parameter is displayed and with the [
], [
] we change the value.
By pressing [
] we
confirm
the new value and the name of the parameter is displayed.
By pressing [
SET
] we
cancel
the new value and the name of the parameter is displayed.
By pressing [
] we
exit
the parameters menu.
SWITCHING ON/OFF THE DEVICE
By pressing [
] more than 3 sec. we
switch ON or OFF
the device.
TECHNICAL SPECIFICATIONS
Power supply: 230VAC 50/60Hz / Maximum power consumption: 3W
It is recommended to use a power supply safety switch: fuse 0,5A (not included)
Cabinet’s temperature sensor PTC 1Κ 25°C / Ακρίβεια: 0.5°C
Serial Input
Relay compressor 250VAC 30A resistive load 2HP
Relay water level and relay ON/OFF 250VAC 10A
Operating temperature: -15÷+55°C / Storage temperature: -20÷+80°C
The device is mounted through panel hole 29x71mm and is restrained with two plastic side brackets / Connection with terminal blocks 18A
SERIAL INPUT
REF-DF-SM
can connect to the
key programmer
or to the data logger
Mini Logger
or to the
KIOUR
CAMIN
network or to any
modbus network
.
Key programmer:
controller’s parameter values can be saved or retrieved from the programming key. Plug in the programming key to the controller and press at the same
time [
SET
]+[
]. The device connects to the key and the message “
Eo
” is displayed. By pressing [
] the device downloads the parameters from the key and the message
“
ro
” = read O.K. or “
rF
” = read Fail is displayed. By pressing [
] the device uploads the parameters to the key and the message “
Yo
” = Write O.K. or “
YF
” = Write Fail is
displayed. In case of failure (
rF
or
YF
) reenter the key to the serial input and repeat the procedure from the beginning. The key can connect to all
KIOUR
devices. If you try
to read the parameters of a different device, message “
rF
” is displayed. At any time, we can perform the aforesaid operation. After 10sec the key is disconnected.
Data logger Mini Logger:
the controller is connected to the data logger via cable and by programming the parameter
Add = 1
. Automatically, based on selected minutes,
the data logger writes to a microSD memory card the controller’s temperatures, status and alarms.
CAMIN network:
the controller can connect to the
CAMIN
network via an interface
NET-INS-485
.
CAMIN
is an PC software application designed to collect information,
watch and fully control a net of
KIOUR
devices while sending SMS and email in case of an alarm. The maximum length of the net can be 1000 meters.
CONNECTIONS - DIMENSIONS
button
Operations
pressed once
pressed more than 3 sec
pressed together
SET POINT indication
confirm new value
-
-
indicates temperature sensors °C/°F
ON/OFF controller
enter parameter’s menu
-
-
df
cancel new value
start manual deFrost
Indications
relay ON
deFrost ON