Kingsman ZDV3620 Installation Instructions Manual Download Page 1

Installation Instructions

Listed Certified for USA. and Canada

The ZDV3620 may be installed in an aftermarket permanently located, manufactured (mobile home), 

where not prohibited by local codes.

This appliance is only for use with the type of gas indicated on the rating plate.

This appliance is not convertible for use with other gases, unless a certified kit is used.

Model Number ZDV3620

Stock #’s: ZDV3620N and ZDV3620LP are Certified to:

ANSI Z21.88b-2003, CSA-2.33b-2003, CSA 2.17-M91, CSA P.4.1-02

Read this complete manual before beginning installation.

These instructions must be kept with the unit for future reference.

FOR YOUR SAFETY

Do not store or use gasoline or other flammable vapors and liquids in the

vicinity of this or any other appliance.

What To Do If You Smell Gas

Do not try to light any appliance.

Extinguish any open flame.

Do not touch any electrical switch.

Do not use any phone in your building.

Immediately call your gas supplier from a neighbour’s phone.

If you can not reach your gas supplier, call the fire department.

A Division of R-Co. Inc.

2340 Logan Avenue

Winnipeg, Manitoba, Canada  R2R 2V3

Ph: (204) 632-1962

Warning: 

Improper installation, alteration, service or maintenance can cause property damage, personal

injury or losses of life. Refer to this manual. Installation and service must be performed by a qualified
installer, service agency or the gas supplier.

Printed in Canada August 27, 2008 Part # 3620-MAN  

“Zero Clearance”

Direct Vent Gas Fireplace

INSTALLER: Leave this manual with the appliance.

CONSUMER: Retain this manual for future reference.

Summary of Contents for ZDV3620






















Reviews: