manualshive.com logo in svg

Kikusui PCZ1000A, Operation Manual, Page: 49 / 100

Share
Download
Kikusui PCZ1000A Operation Manual Download Page 49

PCZ1000A

3-15

3

Ope

ration

3.5.3

Constant Power (CP) Mode

Constant power (CP) mode works by setting a power limit value (W).
Setting range for power limit: 50 W to 1000 W
Fig.3-5 shows the front panel display when set to constant power mode. The input             
terminal measurements are displayed on the upper side.

Fig.3-5

Display is CP Mode

1

If the LED above the LOAD key is on, press the LOAD key to change to               
load-off.

2

Press the P SET key to enable CP mode.

The C.C and C.R LEDs illuminate.

3

Use the rotary knob to set the power limit value.

4

Press the LOAD key to change to the load-on state.

The LED above the LOAD key illuminates and current flow starts.

 0.00Ar 0.0Ap 179.6V
-- PSET    1050W  --

RMS current value

Peak current value

RMS voltage value

Power limit

 0.00Ar 0.0Ap 179.6V
-- PSET    1050W  --

 0.00Ar 0.0Ap 179.6V
-- PSET     800W  --

 4.46Ar 6.3Ap 179.4V
-- PSET     800W   --

Summary of Contents for PCZ1000A





































































































Reviews:

No comments