manualshive.com logo in svg

Kikusui DME1500, Operation Manual, Page: 67 / 76

Share
Download
Kikusui DME1500 Operation Manual Download Page 67

DME1500

 

MAINTENANCE

 E-31

 

Chapter 5

MAINTENANCE

 

The following instructions are executed by qualified personnel
only. To avoid electrical shock, do not perform any servicing other
than the operating instructions unless you are qualified to do so.

 

5.1

Cleaning

 

If the panel or any other exterior surface of the product is smeared,
clean the surface by wiping lightly with a soft cloth moistened
with a neutral detergent solution.

 

• Turn OFF the POWER switch before cleaning.
• Never use organic solvents, such as thinner and

benzine, for cleaning.  Use of organic solvents
could result in surface discoloration, marking era-

 

sure, clouded display and so on.

 

5.2

Inspection

 

Check the power code for ruptures in the covering, play or cracks
in the plug and so on.

 

• Ruptures in the covering or any other defect in the

power code could cause electrical shock hazards.

 

Discontinue using the power cable immediately.

 

For purchasing accessories, please contact Kikusui distributor/
agent.

5.3

Calibration

This product was calibrated at shipment. However, recalibration is
required after long-term usage.

For calibration, please contact Kikusui distributor/agent.

CAUTION

WARNING

Summary of Contents for DME1500













































































Reviews:

No comments