manualshive.com logo in svg

Kikusui BIM1000 Series, User Manual

Share
Download
Kikusui BIM1000 Series User Manual Download Page 9

BIM1000 Series

User’s Manual

9

Installation and Preparation

Connecting the Power Cord

This product is designed as an equipment of IEC Overvoltage Category II (energy-consuming equipment 
supplied from a fixed installation).

1

Turn off ( ) the POWER switch on the front panel.

2

Check that the AC power line meets the nominal input rating of the product.

The product can receive a nominal line voltage in the range of 100 Vac to 240 Vac at 50 Hz or 
60 Hz. (Frequency range: 47 Hz to 63 Hz)

3

Connect the power cord to the AC INPUT inlet on the rear panel.

4

Connect the power cord plug to an outlet with a ground terminal.

This completes the connections.

WARNING

Risk of electric shock.

• This product is IEC Safety Class I equipment (equipment with a protective con-

ductor terminal). To prevent electric shock, be sure to connect the protective 
conductor terminal of the product to electrical ground (safety ground).

• The product is grounded through the power cord ground wire. Connect the pro-

tective conductor terminal to earth ground.

• Use the supplied power cord to connect to the AC line.

If the supplied power cord cannot be used because the rated voltage or the plug shape 
is incompatible, have a qualified engineer replace it with an appropriate power cord 
that is 3 m or less in length. If obtaining a power cord is difficult, contact your Kikusui 
agent or distributor.

• Do not use the supplied power cord with other instruments.
• The power cord with a plug can be used to disconnect the product from the AC power 

line in an emergency.

• Secure adequate space around the power plug. Do not insert the power plug to an out-

let where accessibility to the plug is poor. And, do not place objects near the outlet that 
would result in poor accessibility to the plug.

Summary of Contents for BIM1000 Series































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands