manualshive.com logo in svg

Kikusui BIM1000 Series, User Manual

Share
Download
Kikusui BIM1000 Series User Manual Download Page 52

52

User’s Manual

BIM1000 Series

Remote Control | Registers

Event status register

This register notifies the status byte register of the product’s status. There are three types of event status 
registers: standard event status register, event status register 0, and event status register 1. When the 
product’s status changes, the corresponding bit in the event status register is set to 1. If the bit set to 1 is 
enabled, the corresponding bit (ESB, ESB0, ESB1) in the status byte register is set to 1.
To enable the bits in the event status byte register, use the following commands to set the corresponding 
bits in the enable register.
Standard event status enable register: *ESE

 (p. 60)

Event status enable register 0: :ESE0

 (p. 61)

Event status enable register 1: :ESE1

 (p. 61)

Standard event status register (SESR)

&

&

&

&

&

&

ESB

ESB0

ESB1

&

&
&

&

&

&

&

&

Event status 
register 0

EOM

INDEX

NOT USED
NOT USED

ERR

NOT USED

NOT USED

NOT USED

R-Low

R-IN

R-Up

V-Low

V-Up

PASS

V-IN

FAIL

1

0

2
3
4
5
6
7

1

0

2
3
4
5
6
7

Event status 
register 1

Event status 
enable register 1

OPC

OPC
NOT USED
QYE
DDE

CME
NOT USED

EXE

PON

NOT USED

QYE
DDE

CME

NOT USED

EXE

PON

1

0

2
3
4
5
6
7

1

0

2
3
4
5
6
7

Standard event 
status register

Standard event 
status enable register

Event status 
enable register 0

EOM
INDEX
NOT USED
NOT USED

ERR
NOT USED

NOT USED

NOT USED

1

0

2
3
4
5
6
7

1

0

2
3
4
5
6
7

&

&

&

Status byte register

R-Low
R-IN
R-Up
V-Low

V-Up
PASS

V-IN

FAIL

1

0

･

･

･

5

･･

Bit

Bit 
weight

Bit 
name

Description

0

1

OPC

Set when an *OPC command is received and all operations in standby have 
been completed.

1

2

–

Not used

2

4

QYE

Set when an attempt is made to read data from the output queue when there is 
no data or when the output queue is not in the wait state. This indicates that there 
is no data in the output queue.

3

8

DDE

Set when there is a device-specific error.

4

16

EXE

Set when the product evaluates that the program data after the header is outside 
the formal input range or does not match the specifications of the product. This 
indicates that a valid SCPI command may not be executed correctly depending 
on the state of the product.

5

32

CME

Set when an IEEE 488.2 syntax error is detected by the parser, when an uniden-
tifiable header is received, or when a group execution trigger enters the internal 
IEEE 488.2 SCPI command input buffer.

6

64

–

Not used

7

128

PON

Set when the power is turned on.

Summary of Contents for BIM1000 Series































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands